Need under cabinet lighting installation in Tierra Verde? Under cabinet lighting installation in Tierra Verde is a low, even run of light under existing kitchen or bar cabinets, not a new ceiling fixture and not a recessed-can layout. We come from the Seminole shop, about 12 miles away, and we plan the driver, the switch, and the path before we stick the first section of tape or set the first puck. A 1980s kitchen with a dark counter, a later island, or a wet-bar cabinet is the usual ask. We will not staple a loose strip where a proper channel and a listed driver belong.
Request under cabinet lighting installation in Tierra Verde
Tell us what you need and where the work is. A licensed electrician will reply with next steps and a time to visit.
Related work along the Bayway: commercial electrician, commercial generator installation, EV charger installation, generator interlock transfer switch, permanent Christmas lights, panel replacement, permanent lighting, home battery backup, solar wiring support, after-hours electrical help, 240v outlet installation, aluminum wiring repair, apartment multifamily electrical and appliance wiring hookup.
Call or text (727) 476-7079 · open 24/7 for emergencies · request a quote online

Under cabinet lighting installation in Tierra Verde is a planned run under the cabinets you already have
The work sits under the wall cabinets, along a bar, or at a toe-kick if that is part of the same design. We choose a listed LED tape in an aluminum channel with a diffuser, or listed pucks, and we hide the driver where it can stay cool and serviceable. A line-voltage under-cabinet fixture is also an option when the cabinet and the listing support it. We will not leave a driver stuffed in a closed, hot cavity, and we will not power a long tape run from a random receptacle under the sink.
What we usually install
- LED tape in an aluminum channel with a diffuser and end caps, cut and joined to the cabinet layout.
- Listed pucks under a short run of cabinets or a single bar section.
- A dimmable driver or a wall dimmer that is compatible with the tape or the pucks.
- A switch or a dimmer at a convenient door or a cabinet end, on a circuit that can carry the load.
- A short feed from a nearby lighting circuit or a small new drop when the existing switch cannot honestly serve the run.
Drivers, dimmers and a path that stays serviceable
- Florida electrical contractor license EC13014717, licensed & insured
- Woman-owned business based at 6248 Seminole Blvd, Seminole FL 33772
- 2-year workmanship warranty, 5 years with a Member Care Plan
- SPAN Authorized Installer and Home Depot preferred contractor
- Open 24/7 for electrical emergencies: call or text (727) 476-7079
The driver is a device that will need access later. We place it in a cabinet soffit, a pantry side, or another listed, ventilated spot, not taped to a hot upper cabinet. A heat sink, a quick connector, and a listed pigtail keep the low-voltage side serviceable.
If you already have a wall dimmer, we confirm it is the right type for the tape; a leading-edge dimmer on a low-voltage driver is a common source of flicker. A new dimmer or a driver with a listed control can be part of the same visit. We fish the low-voltage leads in a channel or a small raceway so they are not pinched by a hinge or a drawer slide.
Finished kitchens, stone backsplashes and a clean underside
Many kitchens here have a stone or tile backsplash and cabinets that stay in place. We work from the underside, we protect the counter, and we cut the channel so end caps sit clean at the cabinet edge. We will not drill a visible cabinet face when a hidden end-feed will do.
In an attached villa, a shared wall behind a kitchen may need written association approval if we have to open it. A detached house is usually simpler. A seasonal kitchen that has sat unused can also show a tired under-cabinet fluorescent we are replacing, and we recycle the old ballast and lamps rather than leave them in a drawer.
When a small new drop is needed
If there is no honest switch or feed at the cabinets, we may need a short new drop from a nearby lighting circuit or a small home run. That is new work, and we write the packet when it is required. A simple swap of a failed under-cabinet fixture on an existing feed can stay a service-level ticket. Use the island street on the request, even if a kitchen catalog ships to a mainland mailbox.
After the counters are lit
We dim the run through its full range, we check that the diffuser sits even, and we show you where the driver lives. If a section of tape darkens or a driver hums in the first days, call or text (727) 476-7079 and name the kitchen or the bar. We prefer to reseat a joiner than leave a dark gap under a cabinet. Labor is warranted for two years, and for five years with a Member Care Plan.
Details we use to plan the under-cabinet run
The island street, a photo of the underside of the cabinets, the length of the run, and whether you want tape in a channel, pucks, or a line-voltage bar. Tell us if a dimmer is already on the wall. A kitchen that is in the middle of a remodel should wait until the cabinets are set; we will not stick tape to a cabinet that is about to be pulled.
Hardware we stock for under-cabinet runs
We stock 2700K and 3000K tape, aluminum extrusion, frosted lenses, corner joiners, and dimmable constant-voltage drivers. A valence or a light rail is an option when the cabinet bottom will not hide a channel. We also carry end caps and a spare diffuser so a cut run still closes clean. 12-volt and 24-volt tape, a solderless joiner, and a high-CRI reel are on the van when the kitchen calls for a closer color match.
Mounting clips, a barrel connector, and a polarity mark on the leads keep a long run from being reversed under a dark cabinet. A door-switch lead, an IR hand-wave control, and a spare constant-voltage driver are options when a wall dimmer is not the right control. A lumen rating, a kelvin stamp, and a cut chart on the reel keep the run even from end cap to end cap. A frosted lens clip and a dark-bronze extrusion are on the van for a cabinet with a darker underside. An anodized channel, a polycarbonate lens, and a ferrule on the low-voltage lead finish a clean underside run.
Jobs this page does not cover
A ceiling fixture, a chandelier, a recessed layout, a security flood, and permanent lighting on eaves, soffits, and gable rakes are covered on other pages. A general lighting design for the whole room also has a different home. This page is the under-cabinet run, on the cabinets that are staying.
Common questions
Can you install tape lighting under cabinets that are already in place? Yes. We work from the underside and we hide the driver where it stays cool and reachable.
Will my existing dimmer work with the new tape? Only if it is compatible with the driver. We test that, and we will say if a listed match is needed.
Do you also light a wet bar or a pantry cabinet? Yes, when the same kind of run applies. Tell us the length and the cabinet type when you call.
What do you need in order to price the under-cabinet run? The island street, photos of the underside, the approximate length, and whether a dimmer is already on the wall.
Is a packet required? When we add a new drop or a new switch loop. A replacement on an existing feed can stay a service-level ticket.
How do we schedule the work? Reach us at (727) 476-7079 by call or text, or submit the form. Mention the street and that this is under-cabinet lighting.
The drive from our shop at 6248 Seminole Blvd is about 12 miles. In Tierra Verde we work along the canal lots, the Pinellas Bayway and the open bay front. From here we also reach Madeira Beach, St. Pete Beach, South Pasadena, Gulfport and St. Petersburg.
Up: Under Cabinet Lighting Installation across Tampa Bay · For everything we do locally, see Tierra Verde electrical service.
Call or text (727) 476-7079 for under cabinet lighting installation in Tierra Verde, or book online. Business hours 7 AM–5 PM, weekend service, 24/7 emergency calls.
