Want under cabinet lighting installation in Bay Pines? Keywest Lights & Electric provides under cabinet lighting installation in Bay Pines for kitchens, bars and workshops. We are licensed and woman-owned, and we hide the wire so only the light shows.
Request under cabinet lighting installation in Bay Pines
Tell us what you need and where the work is. A licensed electrician will reply with next steps and a time to visit.
Besides this, our Bay Pines crew handles backup generator hookups, EV charger installation, a business standby generator and a commercial electrician. We also handle jellyfish lighting and panel upgrade replacement.
Call or text (727) 476-7079 · open 24/7 for emergencies · request a quote online

Under cabinet lighting installation in Bay Pines: light where you work
Overhead lights cast shadows on a counter, especially when you stand in front of it. Strips under the cabinets put light right on the cutting board, the coffee station or the workbench. Kitchens in many Bay Pines homes were built around 1970, so a lot of them have a single ceiling light and plenty of dark corners. A good strip fixes that quickly.
Where we install strips
- Kitchen counters: even light on prep areas.
- Wet bars: glasses, bottles and a soft evening glow.
- Laundry cabinets: folding tables and utility sinks.
- Home offices: desks under wall shelves.
- Garage workbenches: bright, shadow-free light.
- Pantries and butler’s pantries: light inside the cabinet.
- Display shelves: gentle accent light on glass or books.
Types of strips
- Florida electrical contractor license EC13014717, licensed & insured
- Woman-owned business based at 6248 Seminole Blvd, Seminole FL 33772
- 2-year workmanship warranty, 5 years with a Member Care Plan
- SPAN Authorized Installer and Home Depot preferred contractor
- Open 24/7 for electrical emergencies: call or text (727) 476-7079
We install linear LED bars, flexible tape in an aluminum channel and low-profile puck lights. Bars give the cleanest line and the best heat control. Tape fits curves and tight gaps. Pucks suit small spots and shallow cabinets.
Hardwired or plug-in
A hardwired strip is tied to a switch and a circuit, with no cords on the counter. We cut a small opening, bring the cable down inside the wall or the cabinet and finish with a plate. A plug-in strip uses an outlet inside the cabinet and a switch near the door. We choose based on your wall, your cabinets and your budget for the job.
Hiding the wire
We run cable inside the cabinet top, behind the trim or within the wall cavity. In block walls, we route through the soffit or the ceiling above. We use a lip or a small rail so the strip stays out of sight from standing height.
Color and brightness
Warm white at around 2700 to 3000 Kelvin makes food look natural, while 3500 to 4000 Kelvin feels crisp for task work. We test with a sample strip before we commit to a color. Mixed colors in one kitchen look odd, so we match the strips and any nearby ceiling lights.
Dimming and switching
A dimmer or a separate switch lets you use strips as a night light or as a bright work light. We install a wall switch, a dimmer or a slim sensor, depending on the room. If your cabinets are backed by tile, we place the control on the side wall so you can find it in the dark.
Glare and reflection
Shiny stone or glossy tile can throw a harsh streak back at your eyes. We mount strips toward the front or back of the cabinet underside, or add a diffuser, so you see light and not the light source.
Working around backsplashes
Tile and slab backsplashes limit where wire can run. We plan the path before the tile goes up when we can, and otherwise we use the cabinet cavity. Our crew protects counters with pads and sweeps up before we go.
Power supply and capacity
Many strips run from a small driver that turns line voltage into low voltage. We mount the driver where it stays cool and reachable. We add up the load on the lighting circuit so you do not overload it.
Planning with a remodel
If you are replacing cabinets or tile, we can run wire during rough-in. That keeps walls clean and lets us set the switch exactly where you want it.
Permits and inspection
Plug-in strips often need no permit. A new hardwired run or a new circuit usually does. We explain what your job needs and handle the paperwork when required.
Power for a wet bar or island
Some counters have no wall behind them. We bring power up through the floor or over from the nearest cabinet side, and we seal the opening so crumbs and moisture stay out. Where an island has an outlet for appliances, we avoid tying lights into the same circuit as a toaster or blender.
Matching the existing look
Brushed or white trim can disappear into a cabinet, while a black bar stands out. We hold samples up before we choose and keep the edge of each strip a little back from the door so the light feels built in.
Sensors and smart control
A slim motion sensor under the cabinet can turn the strip on when you step in. A smart switch lets you set a morning and evening schedule. We set up the app and test it with you.
Tracing a dark corner
Walk the kitchen in the evening and notice where a shadow lands on the knife block, the stove top or the sink. Those spots set our layout. We also check for a cabinet face frame, a crown strip or a raised lip that will hide a bar and shield the glare. Shallow cabinets get a slimmer bar, and deep ones get two short runs so the middle of the counter never falls dark.
Cleaning and long life
Wipe the lens with a soft cloth and a little mild soap, and skip harsh sprays that cloud a diffuser. Quality bars are rated for many thousands of hours, so a good install should serve for years.
Warranty
We stand behind our workmanship for 2 years, or 5 years with a Member Care Plan.
What to expect
Most kitchens take part of a day. We bring drop cloths, test every strip and leave your counters clean.
Common questions
Will under cabinet lights heat up my cabinets? LED strips run cool. We choose a driver and mount that keep heat low.
Can I control them with my existing switch? Often yes. We can wire the strips to a switch or add a dimmer at the wall.
Can you hide the wires with tile already installed? In most cases we route the cable through the cabinet cavity so the tile stays intact.
Our trucks leave the shop on Seminole Blvd, about a mile away, and work near Boca Ciega Bay, Long Bayou, Seminole Boulevard and Bay Pines Boulevard. We also serve Pinellas Park, Kenneth City, Indian Shores, Bardmoor and Redington Shores.
Up: Under Cabinet Lighting Installation across Tampa Bay · For everything we do locally, see Bay Pines electrical service.
Nearby: Seminole
Call or text (727) 476-7079 for under cabinet lighting installation in Bay Pines, or book online. Business hours 7 AM–5 PM, weekend service, 24/7 emergency calls.
