Need dimmer switch installation in Tampa Bay? Keywest Lights & Electric does this work in Pinellas and Tampa Bay as a woman-owned contractor under license EC13014717.
Request a dimmer or switch installation quote.
Tell us which rooms, what kind of lights are on the switch and any problem you have noticed, such as flicker, buzz or heat. A photo of the wall plate helps. A licensed electrician will reply.
Dimmer and light switch installation in Pinellas and Tampa Bay: LED-compatible dimmers, three-way and multi-gang switches, smart switches and fixes for flicker, buzzing and dead controls, done by a licensed electrician.
Lights flickering or need new controls? Call (727) 476-7079 · Describe the switches

Dimmer switch installation in Tampa Bay: the switch decides how the light feels.
A room can have the best fixtures and still feel wrong if the control is wrong. A dimmer lets a dining room go from bright for homework to soft for dinner, and it can make a bedroom or a lanai more comfortable at night. A switch that buzzes, flickers or runs hot does the opposite.
Since the switch to LED lighting, most dimmer problems are matching problems. The dimmer, the driver inside the bulb or fixture and the number of lights on the circuit have to agree with each other.
What we install and fix.
- LED dimmers: controls rated for LED bulbs, recessed lights and fixtures, set up for smooth low-end dimming.
- Three-way and four-way switches: dim or switch one light from two or more places.
- Multi-gang switch banks: a clean group of switches, dimmers and fan controls under one plate, labeled.
- Smart switches and remotes: app, voice and schedule control, after we check the box wiring.
- Occupancy and timer switches: for closets, garages, laundry rooms and shared spaces.
- Repairs: dead, hot, noisy or loose switches replaced and the box checked.
For new fixtures with the switch, see lighting installation. For rows of ceiling lights, see recessed lighting installation.

Getting LED dimming right.
Dimming LEDs is a different job than dimming old bulbs. The load is small, so a dimmer built for hundreds of watts of incandescent light may not hold steady at one tenth of that. Mixed brands on one dimmer can also behave differently from each other.
- Count the load: we add up the lights on the circuit against the dimmer’s minimum and maximum.
- Match the type: the dimmer type is chosen to suit the bulbs or fixtures.
- Set the range: we adjust the low-end level so there is no flicker or drop-out.
- Swap what fails: if one cheap bulb is the problem, we say so and leave your good fixtures alone.
How a switch job works.
- Check the box: we look at the wiring, box depth and what the switch controls.
- Pick the control: single, three-way, smart or multi-gang, matched to the lights.
- Install and label: new devices, a new plate and labels where several switches share a wall.
- Test the lights: we run the range from low to full and leave the room working.

Who does the work.
Keywest Lights & Electric is a woman-owned, licensed and insured Florida electrical contractor (EC13014717) based at 6248 Seminole Blvd in Seminole. Home Depot lists us as a preferred contractor, our installs are backed for two years, and we answer emergency calls around the clock.
Getting dimmer switch installation in Tampa Bay right with LED lamps.
Dimmer switch installation in Tampa Bay has one problem that shows up more than any other: an older dimmer paired with new LED lamps that flicker, buzz or drop out at the bottom of the slider. We check the load, the lamp type and whether the switch is a forward-phase or a trailing-edge dimmer, then install a compatible control. Three-way stairs, multi-gang boxes and smart switches are part of the same visit when the wiring supports them.
A legal switch in the box is the required starting point. We still match the dimmer to the lamps and to how you actually use the room, so a dining room can go low without strobing and a hallway can be set for night. If the box is too shallow or the neutrals are missing, we fix that before the new device goes in.
Specialty dimmer switch installation in Tampa Bay beyond a single slider.
Not every dimmer switch installation in Tampa Bay is a single-pole paddle in a bedroom. Stairwells and foyers need multi-location controls that stay in sync, vanities and under-cabinet strips often want a low-end trim so the lamps do not pop on too bright, and a sunroom or covered porch may need a wet-location or gasketed control. Leftover magnetic low-voltage transformers from older halogen landscapes also need a dimmer listed for that load, not a generic LED-only device.
A listed dimmer in a legal box satisfies the inspection. We still set the low-end trim, confirm the lamps actually dim to the color and brightness you wanted, and label multi-gang devices so the next person can tell a three-way traveler from a switched hot. If a decorator-style device will not fit a shallow or crowded box, we replace the box rather than force the yoke.
Chandeliers, pendants, and crowded boxes in dimmer switch installation in Tampa Bay.
Chandeliers, pendants, and clustered ceiling fixtures are a frequent reason a dimmer switch installation in Tampa Bay feels unfinished. A high-wattage leftover halogen chandelier can overheat a compact LED-only control, and a group of pendants over a table may need a dimmer with a wider load range and a preset or night-light so the room does not jump from dark to bright. We check fixture labels, total load, and whether a companion control is needed at a second doorway.
Pilot-light or illuminated dimmers help in a dark hallway, but the extra current in the handle can keep some LED lamps from turning all the way off. We test for that glow or ripple before we leave, and we change the device or the lamps rather than call the job done. Radio buzz in a nearby speaker is another clue the dimmer and the lamp family are a poor match. You can also read about permanent Christmas lights in Tampa Bay.
Dimmer and switch installation FAQ.
Why do new LEDs flicker after dimmer switch installation in Tampa Bay? Usually the dimmer and the lamps are not a matched pair, or the load is too small for an older dimmer. We check both and replace the control, and sometimes the lamps, so the lights dim smoothly.
Can one dimmer switch installation in Tampa Bay control mixed LED and leftover incandescent lamps? It is a poor mix. The lamps dim on different curves and the older bulbs can keep an LED-rated dimmer from behaving. We usually convert the fixtures to one lamp family and install a control listed for that load so the room dims evenly.
Can dimmer switch installation in Tampa Bay include a preset or a night-light setting? Yes, when the listed control offers a preset or a night-light and the lamps support it. We set that during the visit so a dining room or a hallway comes on at a usable level instead of full brightness.
Why do my LED lights flicker or buzz on a dimmer? Most older dimmers were made for incandescent bulbs and do not control LEDs smoothly. The fix is an LED-rated dimmer matched to the fixtures and the total load on the circuit. We test the combination and set the low-end level so the lights stay steady.
Can any dimmer work with any bulb? No. Dimmers and lamps have to be compatible. The control type, minimum load and maximum load all matter. We choose a dimmer for the bulbs or fixtures you actually have, and if the fixtures are the problem we tell you.
What is a three-way dimmer, and can I dim from two switches? A three-way setup lets two switches control one light, such as at each end of a hallway. Only one of the two switches should be the dimmer, and it must be listed for three-way use. We wire it and label it so both locations work.
Can you replace my switches with smart switches? Yes. Smart switches need the right wiring at the box, often a neutral wire that older boxes do not have. We check the box first, then install and set up the switch with the system you use.
Can a dimmer control a ceiling fan? No, not a light dimmer. Fan motors need a control made for fans. If your fan and light share a wall plate we install the matching controls for each.
The dimmer feels warm. Is that a problem? A little warmth under load is normal. A dimmer that is hot, discolored or that smells is not, and it needs to be replaced right away. Overloaded or loose connections are the usual causes, and we correct those at the box.
Want lights that dim smoothly? Call (727) 476-7079 or use the form above.
See also: All services · Residential electrician · Lighting installation · Recessed lighting installation · Ceiling fan installation · Smart home wiring · Outlets and dedicated circuits
