Meter Base Replacement in Redington Beach, FL

Need meter base replacement in Redington Beach? Keywest Lights & Electric performs meter base replacement in Redington Beach when the meter socket is rusted, cracked, loose or burned. We are licensed and woman-owned, we coordinate the power provider shutoff, install a new base and restore service safely.

Request meter base replacement in Redington Beach

Tell us what you need and where the work is. A licensed electrician will reply with next steps and a time to visit.

This field is required.
This field is required.
This field is required.
This field is required.
How did you hear about us?
This field is required.
This field is required.
This field is required.
This field is required.
This field is required.
This field is required.
This field is required.
This field is required.
This field is required.

In Redington Beach, we also take a commercial electrician, backup generator hookups, backup power for a business and EV charger installation. We also handle jellyfish lighting and panel upgrade replacement.

Call or text (727) 476-7079 · open 24/7 for emergencies · request a quote online

An electrician replacing a meter base
An electrician replacing a meter base.

Meter base replacement in Redington Beach: the box that connects you to the grid

The meter base is the weatherproof box outside your home that holds the meter and connects to the service. Salt, sun and storms wear it out. A damaged base can let in water, arc or leave your service unprotected. We replace it and reconnect everything.

When a meter base needs replacing

  • Rust or flaking metal: salt air has eaten the shell.
  • Cracked or missing cover: water can get in.
  • Burn marks or melted parts: arcing at a connection.
  • Loose from the wall: fasteners have failed.
  • Bent after impact: a vehicle or storm.
  • Old style socket: will not take a new meter or a disconnect.

What a meter base does

  • Florida electrical contractor license EC13014717, licensed & insured
  • Woman-owned business based at 6248 Seminole Blvd, Seminole FL 33772
  • 2-year workmanship warranty, 5 years with a Member Care Plan
  • SPAN Authorized Installer and Home Depot preferred contractor
  • Open 24/7 for electrical emergencies: call or text (727) 476-7079

The base holds the jaws that the meter plugs into. Power from the provider goes in the top, passes through the meter and out to your panel. If any part of that path is worn, the whole house can lose power or shock a person who touches it.

The power provider’s role

The power provider owns the meter and controls the service line. They must disconnect the service before we work and reconnect it afterward. We schedule that visit and are on site when it happens.

Weatherhead and service entrance

The weatherhead at the top of the mast brings service wires down to the base. If it is worn or loose, we replace it with the base. See our weatherhead repair page for more.

Choosing the right size

Bases are rated by amperage, such as 100 or 200 amps. We match the new base to your panel and service and recommend a larger one if you plan to add loads.

Mounting and sealing

We fasten the base firmly to the wall, seal every opening with a rated material and make sure water runs away from the connections.

Grounding the service

The base connects to the grounding electrode system. We check the ground rod, the clamp and the wire, and replace anything corroded.

Salt air and coastal wear

Water covers roughly 73 percent of the town. Salt and humidity eat steel meter bases quickly. We use durable, corrosion-resistant bases and sealed fittings made for coastal homes.

Storm damage

Wind, flying debris and flooding can bend or crack a meter base. After a storm, we inspect the base, the mast and the main panel before power is restored.

Flood-prone areas

In a low spot, the meter base may be too close to the ground. We discuss raising it as part of a service upgrade, within what the code and the power provider allow.

Older homes

Half the homes in town were built by about 1959. Original meter bases may be rusty or an old style that no longer fits a modern meter. A new base often goes in with a panel upgrade.

Condos and meter banks

In a building with ten or more units, meters may sit in a bank. We coordinate with the building manager and the power provider and only replace the unit that serves your home.

Seasonal homes

About 21 percent of units here are seasonal. We can replace a worn base while you are away and leave a note about what we found.

Aging in place

Nearly two in five residents are 65 or older. Losing power affects medical devices and cooling, so we plan the visit around your needs and keep the outage short.

Electric heat and large loads

About 97 percent of homes use electric heat, so the service must carry a big load. We check that the base and the main disconnect are sized for it.

Adding a disconnect or generator inlet

A new base can be a good time to add a service disconnect or a generator transfer setup. We explain the options and quote them together.

Permits and inspection

A meter base swap needs a permit and an inspection, and the power provider reconnects after approval. We handle the paperwork and the scheduling.

What happens on the day

The provider cuts power, we remove the old base, mount the new one, reconnect the conductors, inspect, and call for the reconnect. Plan for several hours without power.

Checking the main panel

Before we leave, we look at the main panel for heat marks, loose lugs or water. A bad base can damage the panel, and we do not leave problems behind.

Cleanup

We remove the old base and any debris, and we leave the wall neat. We can also patch the finish around the new base.

Repairing the mast and clamps

The mast that carries service wires can lean or rust. We check clamps and bracing and make repairs when we replace the base.

Reading the signs of heat

Brown or blue streaks on the cover, a smell like hot plastic, and a humming sound all point to a bad lug or a worn jaw. Tell us what you notice, and we will inspect before it grows into an outage.

Why jaws wear out

The jaws grip the blades of the meter. Over years of heating and cooling they lose tension, and a loose grip creates heat. A new base restores a firm bite.

Lug torque and anti-oxidant

Each lug must be tightened to a set torque and coated with a compound that resists corrosion. We use a torque tool and record the values we reach.

Weather and wind loads

A tall mast catches wind in a summer storm. We check the brace and the standoff bolts and tighten the base so it does not rock against the wall.

Stucco and block walls

Mounting into stucco or block needs the right anchors and a sealant that stays flexible. We choose masonry anchors, drill carefully and seal each hole.

Underground versus overhead service

Some homes take power from overhead wires and others from a buried line. The base and the fittings differ, and we match them to what you have.

Lighting and security around the meter

A small light above the meter helps the reader and discourages tampering. We can add a motion light on the same visit.

Tamper seals and meter rings

The ring that locks the meter belongs to the provider. We leave it for them and make sure the base accepts it.

Notes for property managers

If you manage several units, we can inspect each base on one visit and give you a written list of the condition of each, with photos.

Warranty

We guarantee our labor for 2 years; add a Member Care Plan and that grows to 5 years.

Before we arrive

Clear the area around the meter, note any burning smell or sparks, and tell us if power has flickered.

Safety first

Do not open a meter base or touch the wires. Only the power provider can remove a meter. If you see sparks or smell burning, stay back and call us.

Testing the new base

We test voltage at the base and at the panel, check for heat at each lug and confirm the meter reads properly.

Documenting the work

We keep the permit paperwork and photos of the finished base for your records and for insurance.

Common questions

Can an electrician remove my meter? Only the power provider may pull a meter. We schedule the shutoff and do the base replacement.

How do I know the base is bad? Rust, cracks, burn marks or a loose box are all signs. We can inspect it on a short visit.

How long is the power off? Usually several hours. We coordinate so it is as short as possible.

Our trucks leave the shop on Seminole Blvd, about 2 miles away, and work near Gulf Boulevard and the Intracoastal Waterway. We also serve Redington Shores, North Redington Beach, Indian Shores, Madeira Beach and Bay Pines.

Up: Meter Base Replacement across Tampa Bay · For everything we do locally, see Redington Beach electrical service.

Nearby: Bay Pines · Seminole

Call or text (727) 476-7079 for meter base replacement in Redington Beach, or book online. Business hours 7 AM–5 PM, weekend service, 24/7 emergency calls.