High Bay Lighting Installation in Tampa Bay

Need high bay lighting installation in Tampa Bay? Keywest Lights & Electric installs high bay lighting in warehouses, gyms, workshops and production floors across Pinellas, Hillsborough and Pasco counties. We are a woman-owned contractor under license EC13014717, and we plan layouts, circuits, controls and safe lift access.

Request high bay lighting installation in Tampa Bay

Tell us what you need and where the work is. A licensed electrician will reply with next steps and a time to visit.

This field is required.
This field is required.
This field is required.
This field is required.
How did you hear about us?
This field is required.
This field is required.
This field is required.
This field is required.
This field is required.
This field is required.
This field is required.
This field is required.
This field is required.

Call or text (727) 476-7079 · open 24/7 for emergencies · request a quote online

An electrician hanging a high-bay light
An electrician hanging a high-bay light.

High bay lighting installation in Tampa Bay: good light under a tall ceiling

When a ceiling sits twenty feet or higher, ordinary fixtures do not work. Light must travel a long way, clear racks and reach the floor evenly. High bay fixtures use strong optics and drivers made for tall mounting. Installing them takes lifts, careful circuit design and a plan for maintenance.

Where high bays shine

  • Warehouses: aisles between racks and dock doors.
  • Gyms and courts: even light without glare.
  • Auto shops: bright bays for detailed work.
  • Manufacturing floors: steady light for machines.
  • Churches and halls: tall rooms with big events.
  • Hangars and storage: wide spaces with high roofs.

Surveying the space

  • Florida electrical contractor license EC13014717, licensed & insured
  • Woman-owned business based at 6248 Seminole Blvd, Seminole FL 33772
  • 2-year workmanship warranty, 5 years with a Member Care Plan
  • SPAN Authorized Installer and Home Depot preferred contractor
  • Open 24/7 for electrical emergencies: call or text (727) 476-7079

We measure ceiling height, rack layout, aisle width and work zones. We note beams, ducts, sprinkler lines and cranes. The survey tells us where fixtures can mount and how to route cable. It also shows which areas need more light than others.

Fixture choices

Round fixtures spread light in all directions, linear fixtures suit aisles and wide-beam fixtures suit open floors. Optics are chosen by height and spacing. Lenses come in narrow, medium and wide patterns. We pick the right pattern so racks stay lit and the floor is not patchy.

Light levels and uniformity

A packing area needs more light than a pallet storage aisle. We aim for even coverage, with no dark gaps between fixtures. We use calculations and a handheld light meter to confirm that the result matches the plan.

Mounting methods

Fixtures can hang from chains, pendants, hooks or brackets. We pick supports that suit the roof structure, check load limits and use safety cables on every fixture. Metal buildings often use beam clamps, while concrete ceilings use anchors.

Power, wiring and circuits

High bay loads add up. We plan circuits so a single breaker does not hold the entire floor. Wire routes follow conduit paths that avoid heat and moving equipment. Emergency fixtures sit on a separate, clearly marked circuit.

Controls and sensors

Motion and daylight sensors save energy by lowering light when areas are empty or when skylights provide plenty of light. We mount sensors where they see aisles clearly and avoid false triggers from forklifts or fans. Zones keep lights on only where people work.

Heat, dust and moisture

Warehouses can be hot, dusty or damp. We choose fixtures with the right ingress rating and temperature range. In wet areas, gasketed fixtures and sealed fittings are used. A clean housing and free airflow extend the life of the driver.

Lifts, scaffolds and safety

We use rated lifts and trained crews. Aisles are closed off during work, and spotters watch traffic. Fall protection is used where required. We lock out circuits before opening a fixture or a junction box.

Permits and inspections

Large lighting jobs often need permits. We prepare the paperwork and meet the inspector. Our workmanship carries a 2-year warranty, or 5 years with the Member Care Plan.

Why choose Keywest Lights & Electric

We are licensed, insured and woman-owned. We coordinate with your operations, work in phases and clean up before the next shift. Call or text (727) 476-7079.

Phased installation for busy sites

We install one bay or aisle at a time, so the rest of the floor stays working. We use quiet tools, cover stock and remove debris daily. The plan is shared with shift leads.

Maintenance and spares

We label fixtures by zone, leave spare drivers and share a simple log for lamp or driver swaps. A short yearly check cleans lenses, tightens connections and tests sensors.

Beam clamps, purlins and roof decks

In a metal building, fixtures often hang from beam clamps on the purlins. In a steel joist roof, they hang from clips on the bottom chord. Each clamp has a load rating and a torque value. We check both, add a safety cable and keep wire out of the clamp path.

Chain hangers, hooks and pendants

Chain hangers allow height adjustment, and hooks allow quick swaps. Rigid pendants suit buildings with vibration from forklifts or cranes. We choose a hanger that suits the vibration and the weight, and we leave the cord with a gentle service loop.

Dock doors, loading bays and canopies

Dock lights need to shine into trailers and onto the apron. Some are mounted on the wall with an arm, others on the canopy edge. We aim them to reduce glare for drivers and keep wiring inside protected conduit.

Cold storage and freezers

Cold rooms need fixtures rated for low temperature and condensation. Drivers must start when cold. We use sealed housings and low-temperature gaskets, and we keep cable protected from frost.

Clean rooms, food plants and washdown areas

Food plants need smooth, sealed fixtures that can be hosed down. We choose fixtures with the right ingress rating, avoid dust traps and use stainless fasteners. Light colors help sanitation crews see clearly.

Common questions

How high can you install fixtures? We use lifts rated for typical warehouse heights. Tell us your ceiling height and we will plan the access.

Can you retrofit old metal halide lights? Yes. We replace fixtures or retrofit them when it makes sense.

Do you install motion sensors? Yes.

Can you work around our shifts? Yes, in phases.

Do you plan the layout? Yes, after a site survey.

Do you install emergency lights? Yes.

Do you handle permits? Yes, when needed.

Do you serve my area? We serve Pinellas, Hillsborough and Pasco counties. Call or text (727) 476-7079 to confirm.

Local pages: high bay lighting installation in Seminole, our home base. See also Pinellas County, Hillsborough County and Pasco County service areas, or browse all electrical services.

Call or text (727) 476-7079 for high bay lighting installation in Tampa Bay, or book online. Business hours 7 AM–5 PM, weekend service, 24/7 emergency calls.