Need commercial electrical service upgrade in South Highpoint? Our licensed, woman-owned electricians plan and install a commercial electrical service upgrade for shops and bays in South Highpoint that have outgrown an older service. The Seminole Blvd shop is about 7 miles from this community.
Request commercial electrical service upgrade in South Highpoint
Tell us what you need and where the work is. A licensed electrician will reply with next steps and a time to visit.
You can also book us in South Highpoint for battery backup installation, backup generator hookups, emergency electrical calls and permanent Christmas lights. In South Highpoint we also handle commercial generator installation, ev charger installation, generator interlock transfer switch, panel upgrade replacement and permanent lighting. In South Highpoint we also handle commercial electrician.
Call or text (727) 476-7079 · open 24/7 for emergencies · request a quote online

Commercial electrical service upgrade in South Highpoint starts with a load list, not a guess at a bigger can
A service upgrade is the work of changing the incoming capacity and the gear that serves a business. We add up the nameplates, the cooling, the shop tools and any planned equipment, then we size the new service, the disconnect and the branch gear from that list. A 1970s bay on Ulmerton Road may still be on a service that was plenty for a quiet office and is now short for a compressor, a welder and a walk-in. We will not hang a larger main on a feeder that cannot carry it.
Why these bays run out of room
The surrounding housing and many of the small commercial buildings went up in the mid-1970s. Later tenants add equipment without a new service. Electric cooling and electric water heating are common here, so the summer load is already high before a new machine arrives. We measure, we photograph the existing gear and we write the new size in the quote so the landlord and the tenant see the same number.
What the upgrade usually includes
- Florida electrical contractor license EC13014717, licensed & insured
- Woman-owned business based at 6248 Seminole Blvd, Seminole FL 33772
- 2-year workmanship warranty, 5 years with a Member Care Plan
- SPAN Authorized Installer and Home Depot preferred contractor
- Open 24/7 for electrical emergencies: call or text (727) 476-7079
- A load calculation: nameplates, hours and planned additions, written out.
- New service gear: the main, the meter fittings and a labeled distribution board.
- Feeder work: a correctly sized run from the new service to the suite or the shop.
- Temporary power during the cutover: a plan so the business is not dark longer than it has to be.
- A closeout directory: every new breaker named for the room or the machine.
Landlords, tenants and the meter
The building owner often owns the service while the tenant owns the suite panel. Both have to sign off when the meter or the main changes. We can send a one-page sketch and the load list so a lease review is easier. If the parcel has more than one meter, we map them before anyone calls for a shutdown.
Cutover planning on a working bay
Most of these businesses cannot close for a week. We plan the cutover for an evening, a morning or a day the owner already picked, and we say how long the dark window is likely to be. South Highpoint is a short drive from the shop, which helps us arrive with the gear staged. If a part is late, we do not open the old service until the new gear is on site.
Three-phase, single-phase and leftover equipment
Some bays need a three-phase service for a lift or a large compressor; others only need a larger single-phase service. We will not sell a three-phase upgrade that the equipment does not need, and we will not leave a three-phase motor on a single-phase service with a makeshift converter as a permanent plan. The equipment list decides the path.
How the job proceeds
We confirm the load list, submit the paperwork, set the new gear, coordinate the cutover, test and label. The old cabinet comes out only when the new one is ready to land. We keep a written change log if the plan shifts after the walls are opened.
Reviews and the inspector
A service change goes through a review. Forms are filed, the inspector is met at the required steps, and the gear stays open until the sticker is on. Whoever has the parcel reviews it, even when the suite envelope names another city.
Coverage after the new service is live
New switchgear, feeders and our labor are under a two-year workmanship term. The Member Care Plan at /member-care-plans/ extends that term to five years. A machine added later, without a new calculation, is outside the term.
Nearby parcels
The same kind of service change is available on similar bays in Pinellas Park, Largo and Feather Sound. Send the parcel, the equipment list and a photo of the existing gear to start.
What we will not do
We will not upsize a main and leave an undersized feeder in place. We will not cut a working business over with no written window. We will not land new gear in a room that lacks working clearance. If the building cannot accept the size you asked for, we say so and show the options.
Gutters, parallel feeders and a crowded gear wall
A rain-tight gutter, parallel feeders and a crowded gear wall are common in a 1970s bay that has been added onto. We will not reuse a rusty trough just because it is already on the wall. If the new main needs a clean backboard, a deeper enclosure or a different entry, that is in the quote. Working clearance in front of the gear is marked on the floor before the old can comes off the wall.
CT cans, house meters and a suite that must stay labeled
Some parcels have a house meter and one or more suite meters. We map every can, we keep the house loads on the house side and we relabel the new directory so a future tenant can find a compressor at 2 a.m. A leftover, unmarked breaker in an old can is photographed and retired, not left as a mystery.
A rusted 1970s main and a backboard that will not hold a new can
Some mains in these bays are original to the mid-1970s and the plywood behind them is soft or too small. We replace that backboard, we flash a wall penetration that has leaked, and we keep the new enclosure plumb so a later inspector is not looking at a tilted can. A used switchboard will not be reused just because it is already on the truck.
Common questions
How do you pick the new service size? A: From a written load list and the planned equipment, not from a guess based on the old can.
Will the business have to close? A: Usually only for a planned cutover window. We set that window with you before we start.
Do I need the landlord involved? A: Yes, when the meter or the main is part of the building. We can copy both parties on the quote.
Can you also add shop circuits at the same time? A: Yes, as a listed part of the same plan, or as a follow-up once the new service is live.
Who handles the review? A: We complete the forms and meet the inspector at the required steps.
What should I send to start? A: The parcel address, photos of the existing gear and a list of the machines you run or plan to add.
How do I request a quote? A: Call or text (727) 476-7079, or use the form at the top of this page.
From the Seminole Blvd shop, South Highpoint is about 7 miles away. We know the streets around Roosevelt Boulevard, 34th Street North, 49th Street North and Ulmerton Road and also take work in Largo, Feather Sound, Clearwater, Pinellas Park and St. Petersburg.
Up: Commercial Electrical Service Upgrade across Tampa Bay · For everything we do locally, see South Highpoint electrical service.
Cities next door: Seminole · Bear Creek · Indian Shores · Tierra Verde · Bay Pines
Call or text (727) 476-7079 for commercial electrical service upgrade in South Highpoint, or book online. Business hours 7 AM–5 PM, weekend service, 24/7 emergency calls.
