Who can I call for appliance wiring hookup in Tampa Bay and Pinellas? Keywest Lights & Electric. We’re a woman-owned Seminole contractor, license EC13014717, and we serve all of Pinellas and Tampa Bay.
Request a quote
Tell us what you need and where you are. A licensed electrician will call or text you back to set a time. For an emergency, call (727) 476-7079, 24/7.


Hookups we do
Range and dryer circuits, electric water heaters, tankless units, dishwashers, disposals and garage freezers.
Tankless units
Electric tankless heaters can call for several heavy circuits. Before quoting, we total your home’s load and let you know whether the panel has room.
Permit and warranty
Gas-to-electric conversions
Swapping a gas water heater, range or dryer for an electric or heat-pump model adds load to the house. Before we quote, we run a load calculation with the new appliance included. You’ll know whether the current panel and service can handle it, or whether load management or an upgrade makes more sense.
Generator and backup considerations
Plan to run a fridge, freezer or well pump from a portable generator? We can put those appliances on circuits that are easy to pick at an interlock or transfer switch. That way backup power reaches what matters most.
Induction ranges and electric dryers
Switching from gas to an induction range or adding an electric dryer often means a new 240-volt circuit. We read the appliance’s install sheet for its breaker size and outlet type. We check panel space and the home’s service capacity. Then we run the circuit along the shortest route, and we avoid cutting finished walls where we can.
Disposals, dishwashers and microwaves
Built-in kitchen appliances usually need their own circuits. The 2020 electrical code requires GFCI protection for dishwasher outlets. When we replace a cabinet microwave or add a dishwasher, we confirm the circuit, the outlet spot inside the cabinet and the GFCI setup all match the appliance.
When a new range, dryer or water heater circuit needs a permit, we file it and book the inspection. That appliance wiring is guaranteed two years, five on Member Care. New panels and services also get a whole-house surge protector. Keywest Lights & Electric: woman-owned, license EC13014717. For a hookup, call (727) 476-7079.
Matching the circuit to the appliance
Every large appliance comes with install instructions that list the voltage, breaker size and wire size it needs. We read those before we quote. A new range, dryer or water heater doesn’t always match the old one. A newer dryer may need a four-wire outlet where the old one had three. An induction cooktop may need a bigger circuit than the range it replaces. A tankless water heater may need several dedicated circuits.
If the panel has no room for the new circuits, we look at three options. It may be rearranged, a subpanel may make sense, or a panel upgrade may be the better long-term answer.
Garage freezers, wine coolers and second refrigerators
Appliances that run all day in a hot garage work harder than the ones inside. We check that the outlet has the protection code requires. We also make sure the circuit isn’t shared with power tools that could trip it.
What we look at before a hookup
The nameplate on a range or cooktop sets the breaker and wire size. A wall oven plus a separate cooktop can mean two circuits where one range used to be. Ranges and dryers today use four-wire cords and outlets, with the neutral and ground on separate wires. Older three-wire setups carried them together. An electric water heater normally has its own 240-volt circuit. It also needs a disconnect within sight, or a breaker that can be locked off. Dishwashers and disposals each get a circuit sized to their labels.
Moving an appliance to a new spot
Moving the washer and dryer to the garage, adding a second oven, or putting a range on a kitchen island means a new circuit run. An extension cord or stretched appliance cord won’t do. We plan the route from the panel and check whether the new spot needs GFCI protection. The work goes on the permit when one is required. Gas appliances still need power for igniters and controls. So a gas range or gas tankless heater usually needs a 120-volt outlet close by.
Heat-pump water heaters and smart appliances
Heat-pump water heaters pull heat from the air around them. They draw far less power than a standard electric tank. But most full-size models still expect a 240-volt circuit, open space and a nearby drain. A few newer 120-volt models plug into a normal outlet near the old heater. Before anyone hauls the old tank away, we compare the label on your new unit with the existing breaker, wire size and disconnect.
Wi-Fi ovens, smart dryers and connected fridges use the same basic circuit as any other appliance. What changes is how touchy their electronics are to voltage spikes. That’s one more reason we suggest whole-house surge protection when a kitchen or laundry room is redone. Code doesn’t always require it, but we don’t build to the minimum.
Commercial kitchens versus home kitchens
Restaurant ranges, walk-in coolers and three-phase dishwashers are a different class of work; see our restaurant and commercial kitchen electrical page. At home, the trickiest jobs tend to be older condos with small services. There, a tankless heater or induction range can exceed what the unit’s feeder was sized for. In those buildings, we review the association’s rules and the unit panel’s rating. Then we suggest options, such as a smaller appliance, load management or a planned feeder upgrade.
Start with the full list of KWLE services for the basics.
Appliance wiring hookup in Tampa Bay for ranges, dryers and water heaters
Every hookup is sized to the nameplate, whether it’s a range, a dryer, or a tankless or heat-pump water heater. Moving a hookup to a new wall, or converting a gas spot, is quoted from the circuit we can actually land. We don’t quote from the box photo alone.
Appliance wiring questions
Can a heat-pump water heater reuse my old water heater circuit? Sometimes. Many 240-volt heat-pump models accept the existing circuit if the breaker and wire size match the installation manual. We confirm that, and the disconnect, before the swap.
Can you hook up a new electric range or dryer? Yes. We check that the circuit and receptacle match the appliance, and replace them if needed.
Do I need a new circuit for an induction cooktop? Often, yes. Many induction ranges need a 40- or 50-amp 240-volt circuit. We check the existing circuit and wire size and replace them if they don’t match the appliance’s requirements.
Can you move a dryer receptacle to the new laundry spot? Yes. We extend or rerun the circuit, install the correct receptacle for your cord, and make sure the vent and the receptacle location work together.
Is it OK to plug a refrigerator into an extension cord? We don’t recommend it. A refrigerator should plug directly into a receptacle on an adequate circuit; if the cord won’t reach, we can add a receptacle.
Can I plug a new dryer into my old outlet? Only if the cord and receptacle match and the circuit is the right size. Many newer dryers need a four-wire connection. We can replace the receptacle and update the circuit if needed.
Do you install the appliance too? We handle the electrical connection and circuit. Plumbing and gas connections are done by the appropriate trade.
More home wiring help in Pinellas · Hillsborough · Pasco
Related: Panel upgrades. You can also read about JellyFish lights in Tampa Bay.
