Under Cabinet Lighting Installation in South Highpoint, FL

Need under cabinet lighting installation in South Highpoint? A 1970s kitchen, a duplex galley or a manufactured kitchen that needs a listed LED run and a driver with a listed home is under cabinet lighting installation in South Highpoint from Keywest Lights & Electric. The Seminole Blvd shop is about 7 miles from here. We are licensed and woman-owned.

Request under cabinet lighting installation in South Highpoint

Tell us what you need and where the work is. A licensed electrician will reply with next steps and a time to visit.

This field is required.
This field is required.
This field is required.
This field is required.
How did you hear about us?
This field is required.
This field is required.
This field is required.
This field is required.
This field is required.
This field is required.
This field is required.
This field is required.
This field is required.

Homes in South Highpoint also call us for business electrical work, commercial generator installation, EV charger hookups, generator installation, generator interlock and transfer switch work, permanent Christmas lights, panel upgrade or replacement, permanent lighting on the soffits and a new 240-volt receptacle.

Call or text (727) 476-7079 · open 24/7 for emergencies · request a quote online

An electrician fitting under-cabinet lighting in a kitchen
An electrician fitting under-cabinet lighting in a kitchen.

Under cabinet lighting installation in South Highpoint is a listed run under the wall cabinets

This page is lighting under the wall cabinets: a slim LED tape or a listed bar, the driver or transformer and the switch or dimmer that controls it. It is not a pendant over an island, not a ceiling fixture and not eave lighting. Those jobs have their own pages. We stay under the cabinets.

1970s kitchens and a short, honest run

Many kitchens here date to the mid-1970s, with short wall-cabinet runs and a shallow soffit above the cabinets that we do not treat as an eave. We measure the run. We cut or order a listed length. We do not staple a loose strip to the front edge and call it finished. The light aims at the counter, not at a neighbor’s window.

Plug-in kits versus a hardwired driver

  • Florida electrical contractor license EC13014717, licensed & insured
  • Woman-owned business based at 6248 Seminole Blvd, Seminole FL 33772
  • 2-year workmanship warranty, 5 years with a Member Care Plan
  • SPAN Authorized Installer and Home Depot preferred contractor
  • Open 24/7 for electrical emergencies: call or text (727) 476-7079

A plug-in kit that sits on the counter is not the same as a hardwired, listed driver hidden in a cabinet or in a listed enclosure. We tell you which method you are getting. We do not hide a plug-in brick where it can fall into a toaster gap and call that a hardwired job.

A driver that needs a home that can shed heat

A driver stuffed in a closed, hot cabinet can fail early. We pick a listed location with the air the listing calls for. We do not bury a driver against a cooktop chase. If the only space is too hot, we say so and we pick another listed spot.

Duplex galleys and a cabinet the tenant does not own

In a rented galley, the cabinets belong to the owner. We need approval before we drill, staple or run a new cable. We keep the work under the wall cabinets we were hired to light. We do not drill an upper cabinet on a tenant request alone.

Manufactured kitchens and a thin cabinet rail

A manufactured kitchen can have a thin cabinet rail and a short backsplash. We use listed clips and a run that fits that rail. We do not over-promise a deep bar where the rail cannot hide it. If the factory wiring is the limit, we say so.

Toe-kicks, insides and a different request

Lighting inside a cabinet or in a toe-kick is a different layout. We will quote it as its own scope if you want that. This page is the underside of the wall cabinets. We do not treat a toe-kick as the same run.

What this page will not install

We do not hang pendants, chandeliers or recessed cans here. We do not run permanent lighting on eaves, soffits or gable rakes on this ticket. We do not invent a review, a price or a utility name.

A close-out card with the run length

We leave a kitchen card when we finish. It records the run length, the driver location and the switch or dimmer we landed. Keep that card with the kitchen papers.

Forms when we open a wall or add a switch

A listed low-profile run fed from an existing switched kitchen circuit can be a brief stop. A new switch location, a new cable or a cut in the wall usually means paperwork. When forms are required we complete them, then we wait with the job if an inspector is booked. A Clearwater return address on the mail does not move the parcel out of unincorporated Pinellas rules.

How this kitchen lighting is covered

Workmanship on the run, the driver and the switch we install carries two years of coverage. With the Member Care Plan at /member-care-plans/, that workmanship period runs five years. An owner-supplied strip that fails on its own stays outside coverage.

A sink window and a reflection we will not ignore

A run over a sink under a window can bounce light back at the glass at night. We aim the diodes at the counter and we set the brightness with a listed dimmer when that helps. We do not point a raw strip at the window and hope the curtain hides it.

A grease-prone cooktop bay

The bay over a cooktop collects grease. We use a listed product that can live in that bay, or we stop the run short of that bay and we say so. We do not leave a paper-backed strip over a cooktop.

An old fluorescent puck still stuck under a cabinet

Some 1970s kitchens still have a tired puck or a small fluorescent under a cabinet. We remove it, we cap or remove its feed honestly and we land the new listed run. We do not leave a dead puck next to the new strip.

A corner dead zone between two cabinet runs

A corner where two cabinet runs meet can leave a dark square on the counter. We plan the strips so the corner gets light, with a listed corner connector or a short extra piece. We do not leave a dark corner because the two runs stopped short of the turn.

A glass-door cabinet we will not light from below

Lighting aimed up into a glass-door cabinet is a different look and can glare. This page aims down at the counter. If you want the inside of a glass cabinet lit, that is its own interior-cabinet scope, and we will quote it that way.

A spice rack that blocks the strip

Some wall cabinets have a spice rack or a rail on the underside. We shift the strip or we move the rack with the owner’s okay so the light can reach the counter. We do not hide a strip behind a rack and call the run finished.

A fridge wall with no cabinets and a dark gap

A fridge wall often has no upper cabinet, so the counter beside it stays dark. We will not invent a cabinet to hide a strip there. A small listed puck on the side panel can be a separate, honest add if you want that gap lit.

A farmhouse sink well that stays dark

A deep farmhouse sink can leave a dark well even when the counters are lit. We can add a listed short run aimed at that well if the cabinet above can hide it. We do not leave the well dark and call the whole kitchen done if that sink was part of the request.

A microwave shelf that splits the run

A microwave shelf often cuts the wall-cabinet run in half. We treat each side as its own listed length and we keep the driver honest for both. We do not stretch one strip through a microwave gap.

A tile backsplash we will not drill for a driver

A tile backsplash is a poor place to hide a driver. We keep the driver in a cabinet or in a listed enclosure, not in a hole cut through tile. We do not drill a backsplash for a brick that belongs in a cabinet.

Common questions

Can you install under cabinet lighting in a 1970s kitchen? A: Yes. We measure the run, we pick a listed product and we give the driver a home that can shed heat. A short galley is a normal job here.

Do I have to buy the lights first? A: You can supply a listed product, or we can include a listed run in the quote. We will not install a kit that is not listed for a hardwired kitchen.

Will you work in a rented duplex kitchen? A: Yes, with owner or office approval. We document any holes or cable runs so the office has a record.

Our shop is on Seminole Blvd, about 7 miles from South Highpoint. Crews work near Roosevelt Boulevard, 34th Street North, Ulmerton Road and 49th Street North. We also serve Largo, St. Petersburg, Feather Sound, Pinellas Park and Clearwater.

Up: Under Cabinet Lighting Installation across Tampa Bay · For everything we do locally, see South Highpoint electrical service.

Cities next door: Bay Pines · Seminole

Call or text (727) 476-7079 for under cabinet lighting installation in South Highpoint, or book online. Business hours 7 AM–5 PM, weekend service, 24/7 emergency calls.