Need thermal imaging electrical inspection in Tampa Bay? Keywest Lights & Electric performs thermal imaging electrical inspections across Pinellas, Hillsborough and Pasco counties. We are a woman-owned contractor under license EC13014717, and we scan panels, switchgear and equipment under load, then explain the results in plain words.
Request thermal imaging electrical inspection in Tampa Bay
Tell us what you need and where the work is. A licensed electrician will reply with next steps and a time to visit.
Call or text (727) 476-7079 · open 24/7 for emergencies · request a quote online

Thermal imaging electrical inspection in Tampa Bay: see heat you cannot see
A loose connection makes heat long before it makes smoke. A thermal camera turns heat into a picture, so a technician can find hot lugs, tired breakers and overloaded conductors without touching them. A scan takes minutes and can prevent outages and fires.
What a scan can find
- Loose lugs: warm spots at terminals.
- Overloaded circuits: conductors hotter than their neighbors.
- Worn breakers: one breaker warmer than the rest.
- Unbalanced loads: phases carrying unequal current.
- Failing fuses: hot clips or holders.
- Bad splices: warm points along a run.
- Motor issues: warm bearings and windings.
How the scan works
- Florida electrical contractor license EC13014717, licensed & insured
- Woman-owned business based at 6248 Seminole Blvd, Seminole FL 33772
- 2-year workmanship warranty, 5 years with a Member Care Plan
- SPAN Authorized Installer and Home Depot preferred contractor
- Open 24/7 for electrical emergencies: call or text (727) 476-7079
We scan panels and equipment while they carry normal load. The camera shows a color map where hotter areas look brighter. We compare similar parts and note differences. A part that is much hotter than its twin needs a closer look. We record images and temperatures.
What we need
Equipment must be energized and loaded. We open covers with proper safety gear or use viewing windows if installed. Access to panels, disconnects and motor control centers is needed. We schedule when loads are typical.
Reading the results
A small rise may be a monitor-only item. A moderate rise calls for repair at the next shutdown. A large rise calls for quick action. We rank findings and give a plain report with photos.
Priorities and repairs
Common fixes are retorquing lugs, replacing breakers, cleaning contacts and rebalancing loads. We can make safe repairs during a planned shutdown, then rescan to confirm the problem is gone.
Panels, switchgear and transformers
We scan main panels, subpanels, switchboards, busway and dry transformers. We check feeders and terminations. Each piece has expected heat patterns, and we note anything unusual.
Motors, drives and HVAC
Motors and drives can overheat from bearing wear, dirty vents or loose wiring. We scan disconnects, starters and drives, and check cooling units. Warm spots can show a failing part.
Safety and limits
Thermal imaging shows surface heat, not hidden defects. It does not replace testing or routine maintenance. We explain what the scan can and cannot see. Do not open or touch energized equipment yourself.
Permits and records
Scans do not need permits, but repairs may. We prepare documents when required. Our reports help insurers and managers keep records. Our workmanship carries a 2-year warranty, or 5 years with the Member Care Plan.
Why choose Keywest Lights & Electric
We are licensed, insured and woman-owned. We explain results simply and fix what we find with care. Call or text (727) 476-7079.
Schedule and frequency
Many buildings scan once a year. Older gear or critical systems may need more frequent checks. We can set a calendar and compare images year to year.
Preparing your site
Share one-line drawings if you have them. Tell us which equipment is critical. Keep staff out of electrical rooms during the scan.
Emissivity, reflections and camera settings
Shiny metal reflects heat and can fool a camera. We adjust emissivity settings, use matte tape on test points and avoid reflections from sunlit windows. Careful settings give reliable readings.
Load matters
A connection that looks fine at low load may overheat at full load. We record the current on each phase with a clamp meter at the time of the scan. That number gives the temperature rise context.
Temperature rise and repair priority
A rise of a few degrees above a matching part is minor. A rise of several tens of degrees is serious. We use accepted rise guidelines to set priorities and explain them without jargon.
Roof units, disconnects and rooftop wiring
Rooftop equipment sees sun, rain and vibration. Disconnect lugs loosen and contactors pit. We scan the roof disconnect and unit terminals, which are often missed in regular maintenance.
Before and after comparison
A repeat scan after repairs confirms the fix. We save images by date and compare them from year to year. Slow trends show wear before it becomes a failure.
Reports that managers can use
A good report has a short summary, ranked findings, thermal and visible photos, load readings and a repair list. We avoid jargon and include a glossary page. Managers can pass it to owners and contractors.
Switch gear, busway and long feeders
Long feeders can hide warm splices. We scan along accessible runs, look at joints and plug-in units on busway and note any hot lugs at taps.
Plant shutdowns and seasonal checks
Before a hot season or a busy season, a scan finds trouble while there is time to fix it. We help plan a shutdown for repairs, bringing parts and crew in one visit.
Common questions
What is a thermal imaging inspection? A scan with a heat camera to find hot connections.
Does the power need to be on? Yes. Equipment must run under normal load.
Will you fix what you find? Yes, if you want. We can schedule repairs and rescan.
How often should we scan? Many sites scan yearly.
Can you scan a home? Yes, panels and outlets can be scanned too.
Is the report useful for insurance? It documents conditions on the day of the scan. Coverage decisions are up to your insurer.
Can a scan find every fault? No. It shows surface heat only.
Do you serve my area? We serve Pinellas, Hillsborough and Pasco counties. Call or text (727) 476-7079 to confirm.
Local pages: thermal imaging electrical inspection in Seminole, our home base. See also Pinellas County, Hillsborough County and Pasco County service areas, or browse all electrical services.
Call or text (727) 476-7079 for thermal imaging electrical inspection in Tampa Bay, or book online. Business hours 7 AM–5 PM, weekend service, 24/7 emergency calls.
