Out of breaker space? Ask about subpanel installation in Seminole. Keywest Lights & Electric installs subpanels in Seminole homes and shops to add breaker space where the main panel is full or far away. We are licensed and woman-owned, with our shop on Seminole Blvd, and we size the feeder and breaker from a load calculation.
Request subpanel installation in Seminole
Tell us what you need and where the work is. A licensed electrician will reply with next steps and a time to visit.
On the same streets, we also handle commercial electrician calls, EV charger installation, generator installation and permanent Christmas lights. Also available here: commercial generator installation.
Call or text (727) 476-7079 · open 24/7 for emergencies · request a quote online

Subpanel installation in Seminole: more spaces, close to the load
A subpanel is a smaller panel fed from the main one. It gives you extra breaker slots near a garage, an addition, a pool or a workshop. It also saves long runs of wire. The feeder, breaker and grounding must be sized correctly, and the neutral must be kept separate from ground in the subpanel.
When a subpanel makes sense
- Full main panel: no spaces left for new circuits.
- Garage or workshop: tools, lighting and a charger.
- Addition: new rooms with their own load.
- Pool or spa: equipment circuits near the water.
- Detached building: a shed, cottage or dock.
- Outdoor kitchen: appliances and lights on one feed.
Subpanel or panel upgrade
- Florida electrical contractor license EC13014717, licensed & insured
- Woman-owned business based at 6248 Seminole Blvd, Seminole FL 33772
- 2-year workmanship warranty, 5 years with a Member Care Plan
- SPAN Authorized Installer and Home Depot preferred contractor
- Open 24/7 for electrical emergencies: call or text (727) 476-7079
A subpanel adds slots, but it does not add capacity. If the main service is already near its limit, a bigger panel and service may be wiser. We calculate the load first. If the total fits, a subpanel is a neat answer. If not, we propose a service upgrade and explain why.
Sizing the feeder
The feeder wire and its breaker depend on how much load the subpanel will carry. A 60 amp feeder suits a modest garage. A 100 amp feeder fits a large workshop or an apartment over a garage. Distance matters too, because long runs lose voltage. We pick the wire size and conduit that suit the distance and the load, and we label the breaker at both ends.
Grounding and neutrals
In a subpanel, the neutral bar must float, not touch the metal box, and a separate ground bar must be bonded to the box. A detached building also needs its own grounding electrode. Mistakes here are common in older work and can cause shocks and stray current. We correct any shared neutral problems we find.
Location and clearances
Panels need a clear work space in front, free of shelves and stored items. They cannot sit in a bathroom or a closet in most cases. We choose a spot that is dry, reachable and out of the way of cars and storage. For garages, we mount at a safe height and protect the panel from impact.
Seminole garages and additions
Many local homes have an older main panel with few spaces and a garage that has outlets from several earlier projects. Adding a subpanel often cleans up these circuits, with room for tools, lights and an EV charger. Salt air near Boca Ciega Bay means we use corrosion-resistant fittings in outdoor and garage locations.
Permit and inspection
A subpanel needs a permit and an inspection. We handle both and provide a labeled directory for each breaker. Call or text (727) 476-7079.
Circuit planning for the new panel
Before we mount anything, we list the circuits the subpanel will carry. A garage might need lighting, outlets, a door opener, a compressor and a charger. A workshop may need 240-volt tools. We group loads so heavy users sit on their own breakers, and we leave several empty spaces for later. A good plan avoids overloading the feeder.
Conduit and wire choices
Feeders run in conduit or cable rated for the location. Underground runs to a detached building need a trench at the right depth, with warning tape and the correct fittings. In garages, we protect the wire from impact and heat. We choose aluminum or copper based on the size and the length, and we use the right anti-oxidant compound at terminals when aluminum is used.
Labeling and documentation
Every breaker gets a label, in both the main panel and the subpanel. We mark the feeder breaker clearly, so no one has to guess what it serves. You receive a diagram of the circuits in the subpanel and a note on the size of the feeder. These small details help future electricians and prevent mistakes.
Safe use after installation
We walk you through the new panel: where the main shutoff is, what each breaker does, how to reset a tripped one and how to test ground-fault protection. If you plan to add loads later, call us first, so we can check the capacity. A subpanel is a good tool, but only when the feeder, the main service and the loads still add up.
Mistakes we fix in older subpanels
We often find subpanels where neutrals and grounds share a bar, breakers are doubled up, wires are too small for the breaker or the box has no cover. Some were wired by a previous owner without a permit. We document each problem with photos, correct it and explain what was wrong. A clean subpanel is safer and easier to expand.
Planning for an electric vehicle or tools
If you plan a charger, a welder or a large compressor, tell us now. These loads can use much of a feeder’s capacity. We can size the subpanel to carry them with room to spare, or recommend a larger service when the numbers say so. A short conversation today can prevent a second visit and a second permit later.
Snowbirds, retirees and part-year homes
Many Pinellas households are seasonal. Owners who return in winter often find that a garage freezer, a golf cart charger or a guest suite pushes an old panel past its comfort zone. We tailor the subpanel to those habits, add labeled switches for items you shut down while away and leave a simple card by the door so house sitters know what to leave on.
Common questions
How many circuits can a subpanel hold? Most hold twelve to forty, depending on the size we install.
Can I add a subpanel myself? A subpanel needs a permit and correct grounding. A licensed electrician should do it.
Will a subpanel fix tripping breakers? Only if the trips come from a full panel. We find the cause first.
Can a subpanel feed a detached garage? Yes, with the right feeder, grounding and a separate electrode.
Does a subpanel need its own main breaker? Some do, and some are fed by a breaker in the main panel. We choose based on the layout.
Our trucks leave the shop on Seminole Blvd and work near Tyrone Boulevard, Bay Pines Boulevard, Walsingham Road, Ulmerton Road. We also serve Redington Shores, Treasure Island, Indian Shores, South Pasadena, Gulfport, Pinellas Park, Indian Rocks Beach and West Lealman.
Up: Subpanel Installation across Tampa Bay · For everything we do locally, see Seminole electrical service.
Nearby: Bay Pines · Madeira Beach · Redington Beach · North Redington Beach
Call or text (727) 476-7079 for subpanel installation in Seminole, or book online. Business hours 7 AM–5 PM, weekend service, 24/7 emergency calls.
