Who can I call for pool spa hot tub electrical in Tampa Bay? For pool spa hot tub electrical in Pinellas and Tampa Bay, call Keywest Lights & Electric. We are a woman-owned business with Florida license EC13014717.
Request a quote in Tampa Bay.
Tell us what you need and where you are. A licensed electrician will call or text you back to set a time. For an emergency, call (727) 476-7079, 24/7.


Pool Spa Hot Tub Electrical in Tampa Bay: pool spa and hot tub electrical in Tampa Bay
Pool pumps and heaters, hot tub and spa disconnects, pool and spa lights, and timers. Each circuit gets the GFCI protection the code calls for.
Bonding and safety
NEC Article 680 covers pools and spas, including equipotential bonding of the shell, deck, ladder rails and equipment. If you feel a tingle in the water, stay out and call us.
Pool lights
A dead pool light can be the bulb, the fixture seal, the cord or the GFCI. We test each before replacing the light.
Who does the work
Bonding and older pools
Older pools might have bonding that was never finished or has rusted where it connects to the pump, heater, ladder anchors, and deck. Since much of this grid is underground, we check if electricity flows smoothly between the equipment and metal parts you can touch. We add a bonding wire where tests show there’s a break.
Storm season and pool equipment
Equipment pads can get wet during heavy rain. We check pumps, heaters, and controllers after flooding. We test them before turning power back on. We also replace GFCIs and timers that got submerged. We make sure disconnects still work properly. Call or text (727) 476-7079 for help with pool spa hot tub electrical in Tampa Bay.
A typical pool equipment upgrade
Many pool projects begin with a new variable-speed pump, heater, or salt system. We check that the circuit size and breaker match the equipment’s nameplate. We make sure the equipment is bonded to the pool’s bonding grid. We add or replace GFCI protection where needed by code. If the equipment pad has rusted boxes or brittle conduit, we fix those at the same time.
Lighting, timers and automation
Underwater lights need a low-voltage transformer or a GFCI-protected circuit. This depends on the type of fixture used. When owners change to LED pool lights or add an automation system, we check the junction box height and location. We also look at the conduit to the niche. And we make sure the controller’s relays can handle the loads they switch.
Pools and spas have water and electricity together. This means bonding, GFCI protection, and disconnect placement must be correct before the inspector comes. We get the electrical permit and are there for the inspection. Our family-run, woman-owned business has license EC13014717. We guarantee pool and spa labor for two years, or five under Member Care. Call or text (727) 476-7079 to ask about your equipment pad.
Residential electrician by county: Pinellas · Hillsborough · Pasco
Equipment we connect
We wire pool pumps, variable-speed pumps, heaters and heat pumps, salt systems, automation panels, lights and hot tubs. Variable-speed pumps and automation systems need the right circuit and controls to work as designed. Hot tubs usually need a dedicated circuit and a disconnect within sight of the tub. We read the manufacturer’s instructions and size each circuit to match.
When a pool or spa is added to an older home, the panel may not have room. We check capacity first and tell you if an upgrade is needed.
Repairs after storms
Flooding and lightning can harm pool equipment and controls. Turn off the power if your equipment was underwater or stopped during a storm. Have a professional check it before you turn it back on. Call or text (727) 476-7079 for help with pool spa hot tub electrical in Tampa Bay.
Heaters, heat pumps and the bonding grid
A pool heat pump or electric heater uses more power than the pool pump. We check the electrical panel to make sure it can handle the extra load. Electrical outlets and switches near the water must follow safety rules about how far they are from the pool. New equipment must connect to a bonding grid with the pump, heater, metal parts, and the pool shell. For new pools, we check the bonding before the deck is built. We work closely with the pool builder to make sure everything happens on time.
Older equipment pads
Equipment pads that have been in the sun and sprinkler spray for many years often show rusted boxes, broken pipes, old timers, and missing wires. We fix broken parts, add GFCI safety where it’s needed, and can wire circuits for smart controls or a variable-speed pump.
Emergency shutoffs, disconnects and LED pool lights
Spas and hot tubs need an emergency shutoff switch that can kill the pump motors quickly. The electrical code requires it to be within sight of the tub and at least five feet away from the inside walls, so someone outside the water can reach it. Pool equipment also needs a disconnect within sight of the pump and heater so a technician can safely service them.
Many owners are switching from old incandescent pool lights to LED ones. Some work with the current line-voltage circuit. Others need a transformer for low-voltage use. We check the niche, cord, and bonding before picking a light. A new light in a leaky or poorly bonded niche won’t last long.
Pool equipment pads that grew over the years
A pad that began with one pump often now carries a heater, a salt chlorinator, a booster for the cleaner, an automation panel and maybe spa blowers. Each addition took power from somewhere, and not always neatly. We map every load, check that the subpanel is rated for outdoor exposure, confirm bonding reaches each metal component, and tidy the conduit so future technicians can follow it. Variable-speed pumps also reward a clean supply, since their drives dislike voltage dips.
Heat, sun and the life of outdoor gear
Florida sunshine bakes plastic covers until they crack, and lawn sprinklers soak enclosures daily. Timer mechanisms, relays and contactors inside older load centers wear out quietly. During a service call we swap brittle covers, reseal entries, replace failing contactors, and note anything approaching the end of its useful life, so surprises during summer swimming season become less likely.
For the full overview, see the full list of KWLE services.
Pool electrical in Tampa Bay for pumps, heaters, lights, and bonding
Pool spa hot tub electrical in Tampa Bay covers the equipment pad, the bonding grid, and the lighting or timer the homeowner actually has. After a storm, we check the disconnect and the bond before saying a pump swap will fix the pad.
Pool and spa electrical questions
Does a hot tub need an emergency shutoff switch? Yes. The code calls for one within sight of the tub and at least five feet from its inside walls, so pumps can be shut off quickly. We include it with every spa hookup.
Can you check pool bonding? Yes. We check the equipotential bonding and grounding of pool equipment and fix what is missing.
Does a new pool pump need its own circuit? Usually, yes. Most pumps and heaters need a dedicated circuit sized to their nameplate rating, with GFCI protection for pump motors. We check the existing circuit before the new equipment goes in.
Can you wire a hot tub on a patio? Yes. A hot tub needs a dedicated, GFCI-protected circuit and a disconnect within sight of the tub, at least 5 feet away from it. We plan the route and permit the work.
Why do I feel a tingle in the pool? Stop using the pool and call us. A tingle can mean missing or broken bonding or a fault in equipment, and it needs to be tested before anyone swims.
Why does my pool light not work? It can be the bulb, a failed seal, the wiring or the GFCI. We test the circuit and the fixture to find the cause.
Do hot tubs need a dedicated circuit? Most do. We follow the manufacturer’s requirements and add a disconnect where the code calls for one.
Related: Pool equipment subpanels · Grounding and bonding · GFCI and dedicated circuits · Underground feeder and conduit repair
