Building a pool? We offer pool electrical installation in Redington Beach. Keywest Lights & Electric provides pool electrical installation in Redington Beach for new pools, spas and heaters, including the pump, light, bonding and ground-fault protection. We are licensed and woman-owned, we coordinate with your pool builder and handle the permit and inspections.
Request pool electrical installation in Redington Beach
Tell us what you need and where the work is. A licensed electrician will reply with next steps and a time to visit.
Besides this, our Redington Beach crew handles a standby generator, a business standby generator, a car charger circuit and a commercial electrician. Also available here: jellyfish lighting and panel upgrade replacement.
Call or text (727) 476-7079 · open 24/7 for emergencies · request a quote online

Pool electrical installation in Redington Beach: safe power around water
Water and electricity do not mix, so pool wiring has strict rules. The pump, the light, the heater, the cleaner and the metal parts around the pool all have specific requirements for wire, protection and bonding. We build to those rules and test each part.
What a pool installation includes
- Pump circuit: ground-fault protected, sized to the motor.
- Pool light: low-voltage or protected line-voltage.
- Heater or heat pump: a dedicated circuit and disconnect.
- Equipment bonding: a grid that ties every metal part together.
- Automation and controls: timers, switches and smart control.
- Outdoor lighting and outlets: around the deck.
Planning with the pool builder
- Florida electrical contractor license EC13014717, licensed & insured
- Woman-owned business based at 6248 Seminole Blvd, Seminole FL 33772
- 2-year workmanship warranty, 5 years with a Member Care Plan
- SPAN Authorized Installer and Home Depot preferred contractor
- Open 24/7 for electrical emergencies: call or text (727) 476-7079
We meet the builder early to place the equipment pad, the panel and the conduit runs. A little planning avoids digging up the deck later.
The equipment pad
Pumps, filters and heaters sit on a pad. We place a disconnect and a weatherproof box within reach and within sight of the equipment.
Bonding the pool
Every metal part near the pool must be connected by a bonding wire. This includes rebar, ladders, rails, the pump motor and the light niche. The bond equalizes voltage so no one gets a shock.
Ground-fault protection
Pool pumps and lights must have ground-fault protection. We use breakers or outlets as required and test them each time we leave.
Pump circuits and variable speed
Modern pumps vary in speed to save power. We size the circuit to the motor and wire the controls the maker requires.
Pool lights
LED pool lights are common and use little power. We choose the right transformer and wiring method for the light and the niche.
Heat pumps and heaters
A pool heater or heat pump draws a lot. We run a dedicated circuit, add a disconnect, and size the wire for the load.
Spas and hot tubs
A spa needs its own circuit and a disconnect in view. See our pool spa hot tub electrical page.
Underground conduit
Conduit for the pool runs under the deck or the yard. We mark and photograph the path before the pour or backfill, which helps with future work.
Distance and clearance rules
Outlets, lights and wires must stay at set distances from the water. We lay out the equipment and the deck lighting to meet each rule.
Salt air and salt-water pools
Water covers roughly 73 percent of the town, and a salt-water pool adds chlorine generator wiring. We use corrosion-resistant boxes, stainless hardware and sealed fittings.
Storm and surge protection
A lightning strike can damage a pump or a control board. We install surge protection and recommend that equipment be shut off before a major storm.
Panel capacity
A pool adds load. We check the panel and the service, and add a subpanel or upgrade if needed.
Older homes
A median build year of about 1959 means many homes are older, so the main panel may be small. We inspect it before we plan the pool circuits.
Electric heat and loads
Almost every home heats with electricity, and a heat pump adds to that. We run a load calculation to make sure the service can handle all of it.
Condos and community pools
About one home in four is in a larger building. A community pool belongs to the association, and we coordinate with the manager on any work.
Seasonal use
About one in five units here is seasonal. We can set up timers so the pump runs while you are away and shuts down when it should.
Aging in place
We place switches and lights where they are easy to reach and add bright, glare-free lighting at the steps and entry.
Permits and inspections
A pool needs several inspections, including bonding before the deck is poured. We prepare the paperwork and meet each inspector.
Reading the pool plan
We study the pool drawings for the position of the deck, the equipment pad and the light niche, and we mark the conduit route before concrete is poured.
Trench depth and warning tape
Buried pool wiring must be at a set depth with warning tape above it. We check the depth, photograph it and record the path.
Equipotential grid and rebar
The steel inside the pool shell and the deck is tied together with copper wire. We connect each section and verify continuity with a meter.
Water features and fountains
A waterfall or a deck jet pump needs its own protected circuit. We add the circuit and a control switch at a safe distance.
Pool cleaners and automation
Robotic and booster cleaners need power and controls. We provide an outlet or a hardwired connection and a safe location for the transformer.
Salt chlorine generators
A salt cell needs a dedicated feed and a bond to the pool system. We read the maker’s diagram and wire it to match.
Deck lighting and landscape power
Safe deck lighting uses low-voltage lines or protected circuits. We plan a layout that lights steps and edges without glare.
Emergency shutoff switches
A clearly marked switch within sight of the pool lets anyone cut power fast. We install one where the rules and common sense call for it.
Testing before fill
We test every bond, light circuit and protection device before the pool is filled and again when the equipment is running.
Pump motor wiring and voltage
Many pumps run on 240 volts and some on 120. We check the nameplate and confirm that the supply matches before we energize the motor.
Screen enclosures over pools
A cage over the pool has metal framing that must be bonded. We tie each section of the frame into the bonding grid.
Weatherproof timers and panels
A timer box on the pad keeps the pump on a schedule. We use a metal or plastic enclosure rated for outdoors and label each switch.
Light niches and junction boxes
The junction box for a pool light must sit above the water level and at a set distance from the pool wall. We locate it to meet the rule and keep it dry.
Pool lighting that changes color
Color-changing lights need a controller or a smart hub. We wire the controls and test each color setting.
Choosing wire for wet locations
We choose conductors with a jacket rated for wet and sun-exposed use, and we run them in conduit where the code asks for it.
Retrofit pool equipment
If an older pool gets a new pump or heater, we update the wiring and protection to meet today’s rules and not simply copy the old setup.
Warranty
The workmanship warranty runs 2 years, or 5 years if you enroll in a Member Care Plan.
Before we arrive
Share the pool plan and the equipment list. Mark the location of the panel and any underground lines.
Safety first
Stay out of the pool if a light or equipment is damaged, tingles or trips a breaker. Turn off the pump and call us.
After the install
We test every circuit, bonding connection and protection device, and leave a diagram of what we installed.
Common questions
Does a pool need special wiring? Yes. Pools need bonding, ground-fault protection and wire sized for each device.
Do you work with pool builders? Yes. We coordinate the schedule so each stage lands in the right order.
Can you add a heater later? Yes, as long as the panel has room. We check first.
Our trucks leave the shop on Seminole Blvd, about 2 miles away, and work near Gulf Boulevard and the Intracoastal Waterway. We also serve Indian Shores, North Redington Beach, Madeira Beach, Redington Shores and Bay Pines.
Up: Pool Electrical Installation across Tampa Bay · For everything we do locally, see Redington Beach electrical service.
Call or text (727) 476-7079 for pool electrical installation in Redington Beach, or book online. Business hours 7 AM–5 PM, weekend service, 24/7 emergency calls.
