Need pool electrical installation in Tampa Bay? Keywest Lights & Electric wires pools and spas across Pinellas, Hillsborough and Pasco counties. We are a woman-owned contractor under license EC13014717, and we handle pumps, lights, bonding and ground-fault protection with permits and inspections.
Request pool electrical installation in Tampa Bay
Tell us what you need and where the work is. A licensed electrician will reply with next steps and a time to visit.
Call or text (727) 476-7079 · open 24/7 for emergencies · request a quote online

Pool electrical installation in Tampa Bay: where water and power must never meet
A pool puts water, metal and electricity close together. The rules for that mix are strict, and for good reason. A proper pool installation includes a pump circuit, lights, a bonded grid, ground-fault protection and safe outlets. Done correctly, the pool is quiet, reliable and safe for swimmers.
What pool wiring includes
- Pump circuit: a dedicated breaker for the motor.
- Underwater light: a low-voltage or listed fixture with a sealed junction box.
- Bonding grid: metal parts joined to equalize voltage.
- Ground-fault protection: breakers or outlets that trip fast.
- Equipment pad: a disconnect and tidy conduit.
- Heater or heat pump: a heavy circuit with its own disconnect.
- Outlets near the pool: placed and protected to code.
Pumps and timers
- Florida electrical contractor license EC13014717, licensed & insured
- Woman-owned business based at 6248 Seminole Blvd, Seminole FL 33772
- 2-year workmanship warranty, 5 years with a Member Care Plan
- SPAN Authorized Installer and Home Depot preferred contractor
- Open 24/7 for electrical emergencies: call or text (727) 476-7079
Single-speed pumps are being replaced by variable-speed models that save energy. Both need a correct breaker and wire. We install timers or controllers, label them and leave a simple guide for the pool service tech.
Bonding explained
Bonding connects metal rails, ladders, pumps, heaters and the reinforcing steel in the deck. Without it, voltage differences can build up in the water. We install a bare copper bonding loop and connect every required item. We test continuity after installation.
Pool lights
Underwater lights come in several types. We choose a listed fixture and run the supply through a proper junction box with ground-fault protection. Older lights with a damaged cord can leak current and should be replaced.
Heaters and heat pumps
Heaters draw large loads. We check the existing service, size the circuit and install a disconnect within sight. We follow the maker’s manual on clearance and wire type.
Distance and clearance rules
Overhead wires, outlets, lights and switches have required distances from the water. We measure and mark these. If an existing fixture is too close, we move it.
Ground-fault protection
A ground-fault device compares current going out and coming back. If they differ even slightly, it opens the circuit. Pool circuits need this protection on pumps, lights and outlets in most cases. We test the device at installation and show you how.
Screen enclosures and lanais
Many Tampa Bay pools sit inside a screen cage. The cage frame must be bonded, and lights and outlets must be rated for damp locations. We work around the frame and avoid cutting screens.
Saltwater systems and automation
Saltwater chlorine generators, pool automation and remote controls add equipment. We provide clean power, a disconnect and a safe place for control boxes. We coordinate with your pool company.
Permits and inspections
New pool wiring needs permits and inspections, with bonding checked before the deck is poured. We work with your pool builder to schedule these visits. Our workmanship carries a 2-year warranty, or 5 years with the Member Care Plan.
Why choose Keywest Lights & Electric
We are licensed, insured and woman-owned, and we respect pool safety rules. We explain the plan in plain words and leave a neat equipment pad. Call or text (727) 476-7079.
Working with pool builders
The builder digs and forms the shell; we run conduit and bonding. Timing matters: bonding steel must be connected before concrete is placed. We coordinate dates, visit for the inspection and return for final connections after the plaster.
Repairs on older pools
Older pools may have missing bonding, cracked light cords or pumps without ground-fault protection. We inspect, report and repair. Upgrading to a variable-speed pump often calls for a circuit update too.
Equipotential grids in new decks
Before concrete is poured for a deck, a copper grid or the rebar mesh is tied to the bonding loop. The goal is a deck where every metal item sits at the same voltage. We tie wire to rebar with listed clamps and take photos for the inspector.
Wet-niche lights and dry-niche lights
Wet-niche fixtures sit in water in a niche in the wall. Dry-niche designs sit behind a lens in a dry housing. Each uses a different junction and cord. We choose the right parts when replacing or adding a light, and we check the transformer on low-voltage models.
Cord length and pool light replacement
When a light is replaced, extra cord must remain coiled in the junction box so it can be lifted out for service. We leave the proper slack, seal the entry and test the ground-fault device afterward.
Pool covers, robotic cleaners and remote controls
Automatic covers and robotic cleaners add small motors. Each needs a safe supply, often a dedicated ground-fault outlet at the pad. We place the outlet away from splash and show you how to unplug equipment for service.
Safe distance from overhead lines
Overhead service lines must stay clear of the pool and the diving area. If lines are too low or too near, a mast change or a rerouted drop may be needed. We measure, document and coordinate with the power company.
Chlorinators, salt cells and flow switches
A salt cell needs a flow switch that proves water is moving, or it can overheat. The control board sits near the pump with a separate disconnect. We confirm the wire gauge from the maker’s sheet and keep low-voltage cable away from the pump motor.
Night swimming and landscape glow
Soft lights around the deck, a path to the gate and a light by the spa steps make evening swims safe. We place fixtures out of the splash zone, aim them down and use sealed splices.
Common questions
Does a pool need a permit for wiring? Yes, in most cases. We pull the permit and schedule inspections.
What is pool bonding? A copper connection between metal parts so voltage stays equal.
Can I plug a pump into a regular outlet? Most pumps need a dedicated circuit and ground-fault protection.
Can you replace a pool light? Yes. We use a listed fixture and sealed junction box.
Do you wire heat pumps? Yes, with disconnects and proper wire.
Do you work with pool builders? Yes.
Can you wire a saltwater system? Yes, with clean power and a disconnect.
Do you serve my area? We serve Pinellas, Hillsborough and Pasco counties. Call or text (727) 476-7079 to confirm.
Local pages: pool electrical installation in Seminole, our home base. See also Pinellas County, Hillsborough County and Pasco County service areas, or browse all electrical services.
Call or text (727) 476-7079 for pool electrical installation in Tampa Bay, or book online. Business hours 7 AM–5 PM, weekend service, 24/7 emergency calls.
