Multifamily New Construction Electrical in Tampa Bay

Need multifamily new construction electrical in Tampa Bay? Keywest Lights & Electric wires new apartments, townhomes and condominiums across Pinellas, Hillsborough and Pasco counties. We are a woman-owned contractor under license EC13014717, and we plan services, meter stacks, unit panels, common areas and life-safety circuits with builders.

Request multifamily new construction electrical in Tampa Bay

Tell us what you need and where the work is. A licensed electrician will reply with next steps and a time to visit.

This field is required.
This field is required.
This field is required.
This field is required.
How did you hear about us?
This field is required.
This field is required.
This field is required.
This field is required.
This field is required.
This field is required.
This field is required.
This field is required.
This field is required.

Call or text (727) 476-7079 · open 24/7 for emergencies · request a quote online

An electrician wiring a multifamily building frame
An electrician wiring a multifamily building frame.

Multifamily new construction electrical in Tampa Bay: repeatable, code-ready homes

Building thirty homes in one project means repeating the same electrical plan thirty times. Consistency, speed and inspection success matter. We design the system once, test it in a model unit and roll it through each building. Residents get safe homes, and builders keep schedules.

Building types

  • Garden apartments: two to four stories with outside stairs.
  • Mid-rise: elevators and corridors.
  • Townhomes: attached homes with separate meters.
  • Condominiums: owned units with shared systems.
  • Senior living: accessible units and emergency call systems.
  • Mixed-use: shops on the ground floor.

Service and metering

  • Florida electrical contractor license EC13014717, licensed & insured
  • Woman-owned business based at 6248 Seminole Blvd, Seminole FL 33772
  • 2-year workmanship warranty, 5 years with a Member Care Plan
  • SPAN Authorized Installer and Home Depot preferred contractor
  • Open 24/7 for electrical emergencies: call or text (727) 476-7079

Each unit gets a meter, plus meters for common areas. We plan the meter stack, main disconnect and feeders. The power company sets rules for models and locations. We coordinate transformer pads and lines.

Unit panels and circuits

Each unit has a panel with circuits for lights, outlets, kitchen, laundry, bath and cooling. Arc-fault and ground-fault protection is installed where required. We repeat a labeled layout so every panel looks the same.

Common areas and corridors

Corridors, stairs, lobbies, laundries and mail rooms need lights, outlets and emergency circuits. We use sensor controls where allowed and design fixtures for easy replacement.

Life-safety systems

Smoke alarms, fire alarm panels, exit lights, emergency lights and stair pressurization fans need power. We run dedicated circuits and coordinate with the alarm and fire protection contractors. Backup power may serve some loads.

Elevators and pumps

Elevators, fire pumps and booster pumps need large circuits and disconnects. We follow the vendor’s sheets and verify voltage and phase. We coordinate shutdowns and testing.

Site lighting and amenities

Parking lots, walkways, pools, gates and clubhouses need power. We plan conduits, poles and photocells. Pool equipment gets bonding and ground-fault protection.

EV charging and future capacity

New buildings should plan for chargers. We install conduit and panel space so chargers can be added later. Load management helps keep service size down.

Schedule and coordination

Repeating floors let crews move in sequence. We stage materials, label bundles by unit and keep a log of rough, trim and final inspections. Clear logs prevent delays.

Permits and inspections

Multifamily buildings require plan review, phased inspections and final approval. Our team prepares the electrical set, attends each inspection and tracks corrections. Our workmanship carries a 2-year warranty, or 5 years with the Member Care Plan.

Why call Keywest Lights & Electric

Builders pick a licensed, insured, woman-owned crew that finishes floors on schedule and documents every unit. Call or text (727) 476-7079.

Model unit and quality control

We build and test a model unit first. The builder and inspector review it, and then we repeat. This catches mistakes early and keeps rework low.

Handover to property managers

We deliver panel schedules, meter maps, common-area drawings and test sheets. Managers can service the building without guessing.

Breezeways, stairwells and egress lighting

Stair lights must stay on during an outage. We wire emergency fixtures on dedicated circuits, test the battery units and label each one. Tenants should never face a dark stair.

Trash rooms, laundries and mail areas

Shared rooms need steady light, ground-fault outlets and sometimes ventilation fans. We use durable fixtures and keep wiring in protected conduit.

Fire alarm interfaces and door locks

Fire alarm panels, door holders and access control all need power. We run circuits to each device and coordinate with the vendors.

Smart meters, sub-meters and billing

Some owners bill tenants for power through sub-meters. We plan meter positions, wiring and access for readers.

Noise control and fire separation

Shared walls and floors must keep fire ratings. We seal penetrations with listed materials and use sound-rated boxes in party walls.

Prefab walls, panelized framing and pre-wired boxes

Many builders use panelized walls with boxes already placed. We review the layouts, verify heights and run cable through the panels on site. Mistakes in prefab walls are costly to fix, so we check each type before production.

Electric ranges, dryers and water heaters

Each unit has an oven, a dryer and a water heater, or shares central systems. We plan wire sizes, outlets and disconnects for each and keep a consistent layout, so maintenance crews know where things are.

Central cooling, chillers and rooftop units

Larger buildings use central plants. We bring feeders to chillers and pumps, add disconnects and coordinate controls with the mechanical contractor.

Surge protection and power monitoring

We install surge devices at the main and, where needed, at each meter stack. Monitoring can show load patterns to managers and help with future planning.

Accessible units and visual alarms

Some units need visual smoke alarms, lowered switches and extra clearance. We follow the accessibility plan and test each device.

Punch lists and warranty walks

Before handover we walk each floor with the builder and make a punch list. Small items, such as a loose cover or a missing label, are fixed that week.

Common questions

Can you wire a new apartment building? Yes.

Do you handle meters and service? Yes, with the power company.

Can you plan for EV chargers? Yes, with conduit and panel space.

Do you wire common areas? Yes.

Can you coordinate with alarm contractors? Yes.

Who handles permit paperwork? We prepare and file it.

Can you keep up with the builder’s schedule? We stage crews by floor.

Where do you work? Across Pinellas, Hillsborough and Pasco counties. Call or text (727) 476-7079 with your address.

Local pages: multifamily new construction electrical in Seminole, our home base. See also Pinellas County, Hillsborough County and Pasco County service areas, or browse all electrical services.

Call or text (727) 476-7079 for multifamily new construction electrical in Tampa Bay, or book online. Business hours 7 AM–5 PM, weekend service, 24/7 emergency calls.