Need high bay lighting in Bay Pines? Keywest Lights & Electric provides high bay lighting installation in Bay Pines for warehouses, workshops, gyms and large commercial spaces. We are licensed and woman-owned, and we use lifts, careful layouts and efficient LED fixtures.
Request high bay lighting installation in Bay Pines
Tell us what you need and where the work is. A licensed electrician will reply with next steps and a time to visit.
Around Bay Pines we also put in generator installation, shop and office electrical work, a car charger circuit and commercial generator installation.
Call or text (727) 476-7079 · open 24/7 for emergencies · request a quote online

High bay lighting installation in Bay Pines: light for tall spaces
High ceilings call for strong, even light. Old metal-halide and fluorescent fixtures run hot, waste energy and fade over time. We replace them with LED high bays and install new ones where a space has gone dark.
What we install
- Round and linear LED high bays: warehouses and shops.
- Fixture hangers and chains: solid mounting to steel or joists.
- Sensors: occupancy and daylight control.
- Dimmers and zones: different areas, different levels.
- Emergency lighting: battery packs and exit signs.
- Wiring upgrades: feeds, boxes and controls.
- Gym and court lighting: glare-controlled layouts.
Planning the layout
- Florida electrical contractor license EC13014717, licensed & insured
- Woman-owned business based at 6248 Seminole Blvd, Seminole FL 33772
- 2-year workmanship warranty, 5 years with a Member Care Plan
- SPAN Authorized Installer and Home Depot preferred contractor
- Open 24/7 for electrical emergencies: call or text (727) 476-7079
We measure the room, the ceiling height and the work areas. A lighting plan sets fixture count, spacing and brightness so aisles, benches and shelves are all well lit.
Retrofits
A retrofit may reuse existing wiring and mounting points. We check the circuits, the boxes and the structure before we hang anything new.
Lifts and safety
High bay work needs a scissor lift or boom. We set cones, use fall protection and keep the area clear. We work around forklifts and staff.
Color and brightness
Cool white at higher output suits warehouses. A warmer, softer tone suits gyms and community spaces. We test a sample fixture before we commit.
Sensors and savings
Motion sensors in the aisle save power when the room is empty. Daylight sensors dim fixtures near skylights and large doors.
Humid and coastal conditions
Bay air corrodes metal. We choose fixtures with sealed housings and coated finishes, and we seal conduit entries.
Fixture mounting
We hang from structural steel or joists, add safety cables and secure junction boxes. Each fixture is tested after the install.
Emergency egress
We check that exit signs and egress lights are working, replace tired battery packs and add fixtures where code requires.
Wiring and circuits
A new fixture layout may need new circuits or larger feeders. We check capacity and update panels where needed.
Permits and inspection
Large lighting projects are permitted. We prepare the paperwork and inspection, and we fix any note right away.
Foot-candles and light levels
Different work needs different brightness. A warehouse aisle needs less than an assembly bench. We measure with a light meter and adjust spacing until each area reaches the target level.
Obstacles and racking
Tall racks, ducts and cranes block light. We place fixtures in aisles, avoid shadows from beams and use lenses that spread or focus the light as needed.
Choosing between round and linear fixtures
Round units suit open floors, while linear strips fit aisles and long benches. We often mix both, selecting each for its job.
Dust, moisture and cleaning
Sealed fixtures keep dust and insects out and wipe clean with a damp cloth. In wet areas, we choose a higher ingress rating.
Zones and schedules
A timer or a lighting controller can dim the space at night or switch off unused zones on weekends. We set the schedule with the manager.
Disposal and recycling
Old fixtures and ballasts may contain materials that need proper disposal. We take them away and recycle where possible.
Skylights, dock doors and daylight
Spaces with skylights or open dock doors see big swings in daylight. We pair sensors with dimmable fixtures so light follows the sun and the schedule.
Gyms, courts and event spaces
Athletes need light that does not glare. We aim fixtures from the sides, use diffusers and choose a color temperature that suits play and cameras.
Hanging height and cable management
We set each fixture at a height that clears cranes, ducts and doors. Cables run neatly along steel or conduit, with strain relief at each connection.
Fixing dark corners
A single dark aisle can slow a workday. We map shadows, add fixtures where needed and re-aim others to fill gaps.
Maintenance
LED fixtures need little care, but dust builds up. We suggest a yearly wipe-down and a check of sensors and emergency units.
Working around operations
We schedule lifts and tools with your staff, stage ladders safely and keep forklifts and foot traffic away from the work area.
Heat, fans and air handlers
Hot warehouse air shortens driver life. We choose fixtures with strong heat sinks and keep them away from heater outlets. Where large fans run, we add safety wires to prevent swing.
Auditing the old system
Before we replace anything, we count fixtures, note ballast types and record circuits. The audit tells us how many LED units you need and which circuits can be combined.
Reducing flicker and strobe
Poor drivers can make moving machinery appear to stand still, which is hazardous. We pick drivers with low flicker and test under motion.
Clean wiring above the grid
We tidy the cable above fixtures, label junction boxes and remove abandoned wires so the next service call is simple.
Warranty
We stand behind our workmanship for 2 years, or 5 years with a Member Care Plan.
Before we arrive
Share the building size, ceiling height and current fixtures. Photos help us plan lift access.
Common questions
Why replace old high bay fixtures? LED fixtures use far less power, run cooler and last longer.
Do you handle lifts and safety? Yes. We bring lifts, cones and fall protection.
Can you add sensors? Yes. Motion and daylight sensors save energy.
Our trucks leave the shop on Seminole Blvd, about a mile away, and work near Boca Ciega Bay, Long Bayou, Bay Pines Boulevard and Seminole Boulevard. We also serve Redington Beach, Madeira Beach, North Redington Beach, Bardmoor and Indian Shores.
Up: High Bay Lighting Installation across Tampa Bay · For everything we do locally, see Bay Pines electrical service.
Nearby: Seminole
Call or text (727) 476-7079 for high bay lighting installation in Bay Pines, or book online. Business hours 7 AM–5 PM, weekend service, 24/7 emergency calls.
