Need commercial panel replacement in Tampa Bay? Keywest Lights & Electric replaces commercial panels, subpanels and breaker equipment across Pinellas, Hillsborough and Pasco counties. We are a woman-owned contractor under license EC13014717, and we plan the shutdown, the new gear and the inspection so your business loses as little time as possible.
Request commercial panel replacement in Tampa Bay
Tell us what you need and where the work is. A licensed electrician will reply with next steps and a time to visit.
Call or text (727) 476-7079 · open 24/7 for emergencies · request a quote online

Commercial panel replacement in Tampa Bay: modern gear for a working building
A commercial panel is the heart of a building. It splits power from the meter into circuits for lights, outlets, cooling and equipment. Old panels run hot, trip often and lack space for new loads. Replacing one needs careful planning, because the whole building depends on it.
Signs it is time
- Frequent trips: breakers open without a clear cause.
- Heat and discoloration: scorch marks on covers or breakers.
- Buzzing: worn breakers or loose bus bars.
- No spare spaces: tenants add loads with extension cords.
- Rust or moisture: corrosion inside the enclosure.
- Obsolete parts: discontinued breakers that cannot be matched.
Evaluating the building
- Florida electrical contractor license EC13014717, licensed & insured
- Woman-owned business based at 6248 Seminole Blvd, Seminole FL 33772
- 2-year workmanship warranty, 5 years with a Member Care Plan
- SPAN Authorized Installer and Home Depot preferred contractor
- Open 24/7 for electrical emergencies: call or text (727) 476-7079
We survey the service, the panel and the loads. We read the nameplate, check voltage and phases and note the available short-circuit rating. We check labels, grounding and bonding. Photos and a short report guide the plan.
Choosing the equipment
Panels are rated by voltage, amps, phase and short-circuit strength. Three-phase four-wire systems are common in commercial spaces. Single-phase panels serve small suites. We select equipment that fits the load and leaves room to grow.
Planning the shutdown
A panel swap needs the power off. We schedule a short window, such as a Sunday or a night, and tell tenants ahead of time. Critical systems can be moved to temporary power where practical. The aim is a clean, quick change.
Coordinating with the power company
If the meter or service entrance changes, the power company must disconnect and reconnect. We schedule that visit and prepare the site so there is no delay.
Labeling and circuit mapping
Every breaker gets a clear label. Many older panels have vague notes like “misc.” We trace each circuit and make a directory. A good map saves hours on later service calls.
Surge and monitoring options
A new panel is a good time to add surge protection or power monitoring. Monitoring shows load patterns and helps catch overloads. We explain what is useful and what is not.
Tenant improvements and sub-metering
Landlords often add panels for new tenants. We plan feeders, meter positions and disconnects to suit leases. Each suite gets its own breaker space and a clear shutoff.
Testing and commissioning
After installation, we torque all lugs, test breakers, check phase rotation and record readings. We provide a short report and leave the panel clean.
Permits and inspections
A commercial panel change needs a permit, often with drawings. We prepare the documents and meet the inspector. Our workmanship carries a 2-year warranty, or 5 years with the Member Care Plan.
Why choose Keywest Lights & Electric
We are licensed, insured and woman-owned. We plan carefully, work neatly and protect your business hours. Call or text (727) 476-7079.
Information to gather first
Have the building address, the panel nameplate photo, a list of major equipment and any single-line drawings. Tell us the hours when a shutdown would hurt least.
Safety rules on site
Only qualified crews open energized equipment. We use lock-out and tag-out, test before touching and mark work zones. Your staff stays clear of the area.
Short-circuit ratings and coordination
A panel must withstand the fault current available at its location. Near a large transformer, that number is high. We review the available fault current and select gear with a matching rating. A coordination check keeps a small fault from tripping the main.
Switchboards, panelboards and load centers
A switchboard serves larger buildings with a main and feeders. A panelboard serves a floor or a suite. A load center serves small spaces. We choose the type that matches the amps and the number of circuits.
Bus bars, torque and thermal imaging
After installation and again after the building runs under load, we measure temperature at the lugs and bus bars. A good connection stays cool. A warm one gets retightened. This step catches loose parts before they fail.
Moving panels and relocating feeders
Sometimes the old panel sits in a bad spot, such as a closet or behind shelving. Code requires working space in front of the equipment. We relocate panels where needed and extend feeders with proper splice boxes or new runs.
Fire-rated walls and penetrations
Panels in rated walls need sealed penetrations. We use approved firestop and keep wall ratings intact. Labels and covers are replaced and logged.
Generator hookups and transfer switches
Businesses that rely on refrigeration or data may want backup power. A transfer switch isolates the building from the grid before a generator feeds it. We size the switch, mount it near the panel and test the changeover. Generators do not qualify for incentives.
Spare capacity and future growth
We leave empty spaces and spare conduit for added tenants or equipment. A panel at eighty percent capacity on day one is a limit, not a plan. Extra room avoids another shutdown.
Common questions
How long does a commercial panel replacement take? Many take one day or a night. Large systems take longer.
Will my business lose power? Yes, for part of the work. We plan the window with you.
Do you need drawings? Often yes. We help prepare them.
Can you add surge protection? Yes.
Do you handle three-phase panels? Yes.
Can you label all circuits? Yes.
Do you handle permits? Yes.
Do you serve my area? We serve Pinellas, Hillsborough and Pasco counties. Call or text (727) 476-7079 to confirm.
Local pages: commercial panel replacement in Seminole, our home base. See also Pinellas County, Hillsborough County and Pasco County service areas, or browse all electrical services.
Call or text (727) 476-7079 for commercial panel replacement in Tampa Bay, or book online. Business hours 7 AM–5 PM, weekend service, 24/7 emergency calls.
Related business services: commercial electrician, woman-owned commercial electrician, apartment and multifamily electrical and church and worship electrical.
