Weatherhead Repair in Bay Pines, FL

Need weatherhead repair in Bay Pines? Keywest Lights & Electric provides weatherhead repair in Bay Pines for homes, condos and small businesses with an overhead service. We are licensed and woman-owned, and we replace cracked caps, repair bent masts, rebuild drip loops and restore a safe, sealed entrance for your wires.

Request weatherhead repair in Bay Pines

Tell us what you need and where the work is. A licensed electrician will reply with next steps and a time to visit.

This field is required.
This field is required.
This field is required.
This field is required.
How did you hear about us?
This field is required.
This field is required.
This field is required.
This field is required.
This field is required.
This field is required.
This field is required.
This field is required.
This field is required.

Neighbors in Bay Pines also book us for generator installation, a car charger circuit, commercial generator installation and a commercial electrician. Also available here: jellyfish lighting and panel upgrade replacement.

Call or text (727) 476-7079 · open 24/7 for emergencies · request a quote online

An electrician repairing a service mast weatherhead
An electrician repairing a service mast weatherhead.

Weatherhead repair in Bay Pines: the cap that keeps water out of your service

The weatherhead sits at the top of the service mast, where the wires from the pole enter a conduit that runs down to your meter. Its curved hood sheds rain, and it holds the wires in a loop so water drips away. When it cracks, tilts or pulls loose, water can follow the wires into the meter and the panel. Salt air and summer storms near Boca Ciega Bay make this part work hard.

Signs that a weatherhead needs repair

  • Cracked or chipped hood: gaps where rain can enter.
  • Mast leaning: after wind, a fallen limb or a hit from a ladder.
  • Wires sagging or pulled tight: no drip loop left.
  • Rust streaks on the mast or meter: water getting in.
  • Flickering lights: after rain or wind.
  • Buzzing or burning smell: a hot connection at the top.
  • Loose service wires: slack or taut between pole and mast.

What we do

  • Florida electrical contractor license EC13014717, licensed & insured
  • Woman-owned business based at 6248 Seminole Blvd, Seminole FL 33772
  • 2-year workmanship warranty, 5 years with a Member Care Plan
  • SPAN Authorized Installer and Home Depot preferred contractor
  • Open 24/7 for electrical emergencies: call or text (727) 476-7079

We inspect the weatherhead, the mast, the clamps and the splices. We then repair or replace whichever parts are worn. That may include a new weatherhead, new connectors, a stronger bracket or a straighter mast.

Why water entry is serious

Water that runs down the service conduit reaches the meter base and the main panel. It rusts lugs, corrodes copper and can cause shorts. Fixing the top of the service early saves bigger repairs later.

A safe process with the power provider

The service wires from the pole are owned by the power provider and stay live. For work that needs the wires disconnected, we schedule a disconnect and reconnect, so the work is done with the power off. We never handle live service wires without that step.

Replacing a cracked weatherhead

We install a new hood rated for the conduit size, seal each wire hole and restore the drip loop. The new part is clamped so it will not twist or lift in a storm.

Straightening or replacing the mast

A bent mast changes the angle of the wires and stresses the meter base. If the mast can be reset, we do it. If it is kinked, rusted or too short, we replace it and rebuild the support.

Brackets, guy wires and clamps

Tall masts need support. We check that brackets are tight on solid framing, that clamps are rated for outdoor use and that any support wire is properly anchored.

Drip loops and wire clearance

Each wire needs a downward loop below the hood. We set the loop height and leave enough slack so wind does not tug the connection. We also check clearance from windows, decks and trees.

Splices, connectors and old wire

Cracked insulation or green corrosion at the splice can heat up. We cut back damaged wire, install listed connectors and cover each splice for weather.

After a storm

High wind and falling limbs can pull a weatherhead off. If you see sparks, a downed wire or a mast hanging loose, stay away and call the power provider and emergency services. After the area is made safe, call us for the repair.

Mobile homes and older cottages

Many homes in this area are older, and some are manufactured homes, about one in six here. Their masts and hoods may be original. We check each part and bring the entrance up to current standards.

Condos and small commercial service

Small buildings may have several meters on one mast. We inspect each connection and coordinate with the manager.

Meter base and panel checks

While we are there, we inspect the meter base, the conduit seal and the panel for moisture. If water got in, we dry, clean or replace damaged parts.

Upgrading to a larger service

If the home needs more power for an air conditioner, a charger or a pool, we can combine weatherhead repair with a service upgrade.

Permits and inspection

Work on the service entrance needs a permit and an inspection. We prepare the filing, schedule the disconnect and meet the inspector.

Reading the parts from the ground

Stand back and look up. A healthy entrance shows a neat hood, two or three insulated wires curving down into it, a straight mast and a tight clamp near the fascia. A tilted hood, a bare spot on a wire or a gap near the cap deserves a closer look.

Fiberglass, steel and PVC options

Masts come in rigid steel and, in some places, other approved materials. We choose the type that suits the home and the local wind exposure, then use fittings made for that material.

Thermal checks at the connection

A warm connection at the top shows up with an infrared camera. We scan the splice after the repair under load to confirm there is no hot spot.

Painting, sealing and finishing

After the repair, we seal the wall penetration, touch up bare metal and leave the mast neat and weather-tight.

Keeping records

You get a short note with the parts replaced, the date and photos, which is helpful for insurance and future owners.

Warranty

We stand behind our workmanship for 2 years, or 5 years with a Member Care Plan.

Before we arrive

Take a photo of the mast and weatherhead from the ground, note any damage and tell us when the problem began. Keep people and pets away from the service wires.

Salt air, rust and long life

Metal parts near the bay corrode faster. We use rust-resistant hardware, seal every joint and recommend a quick check each spring.

Trees, limbs and clearance

A limb that rubs a service wire will wear through the insulation. We note trees that need trimming and advise you to hire a licensed arborist to do it.

Insurance and storm claims

We take photos, record the damage and write a clear summary that you can give to your insurer.

Scheduling and timing

Because the power must be shut off for some steps, we plan the visit so the outage is as short as possible.

Common questions

Is a weatherhead repair an emergency? If wires are down, sparking or hanging loose, treat it as one. Stay away and call emergency services.

Do you handle the power provider disconnect? Yes. We schedule the disconnect and reconnect for the work.

Can you replace the mast too? Yes. We replace bent or rusted masts and rebuild the support.

Our trucks leave the shop on Seminole Blvd, about a mile away, and work near Bay Pines Boulevard, Long Bayou, Boca Ciega Bay and Seminole Boulevard. We also serve North Redington Beach, Bardmoor, Redington Beach, Pinellas Park and Indian Shores.

Up: Weatherhead Repair across Tampa Bay · For everything we do locally, see Bay Pines electrical service.

Nearby: Seminole

Call or text (727) 476-7079 for weatherhead repair in Bay Pines, or book online. Business hours 7 AM–5 PM, weekend service, 24/7 emergency calls.