Need pool spa hot tub electrical in Bay Pines? Keywest Lights & Electric handles pool spa hot tub electrical work in Bay Pines for new installs, repairs and safety upgrades. We are licensed and woman-owned, and we focus on bonding, ground-fault protection and corrosion-resistant wiring.
Request pool spa hot tub electrical in Bay Pines
Tell us what you need and where the work is. A licensed electrician will reply with next steps and a time to visit.
Related jobs near Bay Pines: home EV charging, JellyFish holiday and event lighting, a new breaker panel and backup generator hookups. Just down the road: pool spa hot tub electrical in Seminole. Also available here: commercial electrician and commercial generator installation. Also available here: commercial electrician and commercial generator installation.
Call or text (727) 476-7079 · open 24/7 for emergencies · request a quote online

Pool spa hot tub electrical in Bay Pines: water and power need strict rules
A pool and electricity can be a deadly mix without the right protection. Pumps, heaters, lights and automation all run near water. We bond metal parts, protect circuits with ground-fault devices and keep every connection dry and tight.
What we install and repair
- Pump and heater circuits: breakers, wire and disconnects.
- Pool lights: low-voltage or line-voltage fixtures.
- Bonding grid: metal parts tied together.
- Spa and hot tub hookups: 240-volt circuit and shutoff.
- Timers and controls: schedules and smart panels.
- Outdoor outlets: weather-rated, ground-fault protected.
Bonding and grounding
- Florida electrical contractor license EC13014717, licensed & insured
- Woman-owned business based at 6248 Seminole Blvd, Seminole FL 33772
- 2-year workmanship warranty, 5 years with a Member Care Plan
- SPAN Authorized Installer and Home Depot preferred contractor
- Open 24/7 for electrical emergencies: call or text (727) 476-7079
Bonding ties ladders, rails, pump motors, metal fences and rebar into one grid so no part can become live. We test the grid with a meter and fix loose clamps. A good bond is one of the most important pool safety steps.
Ground-fault protection
Pump and light circuits need protection that trips fast. We test devices, replace failures and label them. A device that will not reset needs a fix, not a taped button.
Spa and hot tub wiring
A hot tub needs a dedicated 240-volt circuit with a disconnect within sight but at a safe distance. We read the nameplate, size the breaker and wire and set the shutoff. Many owners also want a cover lifter, speakers and lights, which we support.
Coastal conditions
About two-fifths of this community is water, and many homes sit near Boca Ciega Bay or Long Bayou. Salt air corrodes plain metal quickly, and screened enclosures trap damp air. We use stainless hardware, gasketed boxes and corrosion-resistant conduit.
Older pools in older homes
With a median build year of 1970, some pools are fifty years old. Original light niches, rusty conduit and missing bonds are common. We inspect, report and offer a repair plan.
Pool lights
LED lights last longer and use less power. We replace old incandescent fixtures, check the niche, replace brittle cords and test the circuit. We also check for water in the conduit.
Pumps, heaters and automation
Variable-speed pumps save power and run quiet. They need correct wiring, a clean ground and the right breaker. We install, test and label. Heaters, salt cells and automation panels have their own circuits.
Lanais and outdoor kitchens
Pool patios often have a grill, a sink and a bar. We add ground-fault outlets, lights and switches with weather covers.
Storm care
Before a storm, shut off the pool breaker. After a storm, check the equipment pad for water and debris before you restore power. We can inspect first.
Condo and shared pools
Community pools need records for the board. We test bonding, replace lights and give the manager a written report.
Equipment pad layout and clearances
Pumps, heaters and filters sit on a pad. The code sets minimum distances from the water, and equipment needs space around it for service. We check the clearances, the slab condition and the conduit path. Water pooling around the pad is a sign of drainage trouble that can shorten equipment life.
Variable-speed pumps and energy use
A variable-speed pump uses a fraction of the power of a single-speed pump when it runs low. It needs a clean supply, a correct breaker and a data cable if it joins automation. We install, program basic schedules and show you how to adjust them.
Salt systems and chlorine generators
A salt cell needs a dedicated circuit and a control board that is protected from moisture. Salt spray corrodes terminals fast. We use sealed enclosures, drip loops and stainless hardware, and we keep the controller out of the splash zone.
Cages, screens and metal bonding
A pool cage is metal, and metal near water should be bonded. We connect the cage frame to the bonding grid at several points and test each connection. Loose clamps and corroded wire are common in older cages.
Evidence for an insurer or a buyer
After a repair or an upgrade, we leave a short report that lists the bonding test, the ground-fault test and the date. A buyer’s inspector will ask for these items, and an insurer may too.
Underwater lights, niches and replacement cords
A pool light niche is a sealed housing in the wall. Old niches rust, and brittle cords crack. Replacing a light means pulling the cord out of the conduit, testing for water and fitting a new gasketed fixture. We keep spare cord length so the light can be serviced without a dive.
Heat pumps, gas heaters and electric heaters
Each heater type needs different power. A heat pump may run on a 240-volt circuit with a disconnect. A gas heater needs a small control circuit and a bonding wire. An electric resistance heater draws a large current. We read the data plate and match the wire and breaker.
Cabana baths, outdoor showers and misters
A cabana bath or a rinse shower near the pool needs ground-fault protection on every outlet and light. Misting fans on the lanai use small pumps that deserve their own protected circuit and a timer so they do not run all night.
Common questions
Do I need a permit? Pool electrical work usually needs a permit and inspection. We handle it.
Why does my pool breaker trip? Water in a light, a failing pump or a damaged cord. We test and fix.
Do pool lights need a transformer? Low-voltage lights do. Line-voltage lights need ground-fault protection.
Can you wire a hot tub? Yes, with a dedicated circuit and disconnect.
Do you check bonding? Yes, with a meter.
How do I schedule a pool electrical check? Call or text (727) 476-7079 and tell us about the equipment.
Our trucks leave the shop on Seminole Blvd, about a mile away, and work near Long Bayou, Seminole Boulevard, Bay Pines Boulevard and Boca Ciega Bay. We also serve North Redington Beach, Indian Shores, Largo, Kenneth City and Redington Beach.
Up: Pool Spa Hot Tub Electrical across Tampa Bay · For everything we do locally, see Bay Pines electrical service.
Nearby: Madeira Beach · Redington Beach · North Redington Beach · Bardmoor
Call or text (727) 476-7079 for pool spa hot tub electrical in Bay Pines, or book online. Business hours 7 AM–5 PM, weekend service, 24/7 emergency calls.
