Adding a mini split in Bay Pines? Keywest Lights & Electric provides mini split electrical installation in Bay Pines for bedrooms, lanais, garages and additions. We are licensed and woman-owned, and we run the circuit, disconnect and control wiring so your HVAC installer can finish the job.
Request mini split electrical installation in Bay Pines
Tell us what you need and where the work is. A licensed electrician will reply with next steps and a time to visit.
Planning more? See our Bay Pines pages for a business standby generator, home EV charging, shop and office electrical work and backup generator hookups.
Call or text (727) 476-7079 · open 24/7 for emergencies · request a quote online

Mini split electrical installation in Bay Pines: power for ductless comfort
A ductless heat pump cools a room without ductwork, which suits lanais, converted garages, in-law suites and older homes with tired ducts. The outdoor unit needs its own circuit and a disconnect, and the indoor head needs a signal cable. We handle the electrical side and coordinate with the HVAC company that mounts and charges the system.
What we provide
- Dedicated circuits: breaker, wire and conduit sized to the nameplate.
- Outdoor disconnects: a sealed box within sight of the condenser.
- Control wiring: the cable between the indoor head and the outdoor unit.
- Multi-zone systems: one feed for several rooms.
- Panel capacity checks: a load calculation before we commit.
- Surge protection: a shield for the inverter board.
- Replacement circuits: updating an older unit’s feed.
The first visit
- Florida electrical contractor license EC13014717, licensed & insured
- Woman-owned business based at 6248 Seminole Blvd, Seminole FL 33772
- 2-year workmanship warranty, 5 years with a Member Care Plan
- SPAN Authorized Installer and Home Depot preferred contractor
- Open 24/7 for electrical emergencies: call or text (727) 476-7079
We look at the panel, the planned head and condenser locations and the route between them. We read the unit’s specification sheet, note the minimum circuit ampacity and sketch a path. You get a written plan before we cut anything.
Sizing the circuit
Most single-zone units need a 15-amp to 30-amp, 240-volt circuit. Multi-zone systems need more. We size the wire and breaker to the label and add a margin where the run is long.
Routing the cable
We run wire through attic space, soffits and utility chases when we can, and use surface conduit on block walls when we cannot. We keep the run short, straight and out of sight, and we seal every wall penetration.
The outdoor disconnect
A disconnect within sight of the condenser lets a technician shut off power safely. We mount it above the splash zone, seal it against salt air and label the circuit in your panel.
Control and communication wiring
Many mini splits use a four-conductor cable that powers the indoor head and carries the signal. We follow the maker’s wiring diagram exactly and label each end, because crossed wires can destroy a board.
Coordinating with the HVAC installer
Mounting, line sets, vacuum and charge belong to your HVAC contractor. We schedule our rough-in ahead of their visit and return for final connections if needed, so no one waits on the other.
Lanais, garages and additions
A new room often needs more than a cooling circuit. We can add outlets, lights, a fan and a switch plan while we are there. For a garage conversion, we plan the whole room at once.
Older panels
Many 1970s panels have little spare room. We explain whether the panel can take the new breaker, whether a subpanel is the better path or whether a panel upgrade makes sense.
Hurricane season hardware
Condensers should be strapped to a pad or bracket, and the wiring should be tight and sealed. We coordinate with your installer on wind-rated mounting and help you decide when to switch off the breaker before a storm.
Noise and vibration
A loose conduit can hum against a wall. We secure it with straps, add a soft isolator where it crosses a stud and keep the box from touching the condenser.
Permits and inspection
A new mini split circuit is permitted work, and the inspector will check the disconnect, the wire and the breaker. We prepare the filing, schedule the visit and correct any note.
Inverter boards and clean power
A ductless unit uses an inverter board that dislikes spikes and loose neutrals. We verify the supply voltage, tighten each terminal to spec and recommend a surge device where storms are frequent. Clean power extends the life of a costly board.
Line-set paths and conduit
Your installer runs refrigerant lines through a wall sleeve, and we plan our conduit to run parallel without crossing it. A tidy, shared path keeps the outside of the house neat and makes later service easier.
Lanai enclosures and sunrooms
A screened lanai turned into a sunroom needs lights, outlets and a fan as well as cooling. We design all the circuits together and leave a few spare conductors for the next change.
Cost-saving sequence
Doing the wiring before the drywall repair, before painting and before the line cover goes on saves a second patch and keeps your finish crew on schedule.
Condensate pumps and drain lines
Some indoor heads need a small pump that removes condensate, and that pump needs a nearby outlet. We add a protected receptacle in the wall cavity and keep it clear of the drain line.
Smart thermostats and Wi-Fi modules
Many ductless units include a Wi-Fi adapter or a wall controller. We run the thin control cable, mount the controller and test the signal with you before we leave.
Warranty
We stand behind our workmanship for 2 years, or 5 years with a Member Care Plan.
Before we arrive
Tell us the make, model and number of zones. If your HVAC contractor has a specification sheet, send us a copy.
Common questions
Does a mini split need its own circuit? Yes. Each outdoor unit needs a dedicated, properly sized circuit and a nearby disconnect.
Can my panel handle another air conditioner? Maybe. We run a load calculation and tell you before the work starts.
Do you mount the indoor head? Your HVAC installer handles mounting and refrigerant lines. We handle the electrical side.
Our trucks leave the shop on Seminole Blvd, about a mile away, and work near Bay Pines Boulevard, Boca Ciega Bay, Seminole Boulevard and Long Bayou. We also serve North Redington Beach, Largo, Pinellas Park, Bardmoor and Redington Beach.
Up: Mini Split Electrical Installation across Tampa Bay · For everything we do locally, see Bay Pines electrical service.
Nearby: Seminole
Call or text (727) 476-7079 for mini split electrical installation in Bay Pines, or book online. Business hours 7 AM–5 PM, weekend service, 24/7 emergency calls.
