Need home addition electrical in South Highpoint? Keywest Lights & Electric handles home addition electrical in South Highpoint when you add a room, a porch enclosure or a small accessory space onto an existing house. We are licensed and woman-owned, and the drive from our Seminole Blvd shop is about 7 miles.
Request home addition electrical in South Highpoint
Tell us what you need and where the work is. A licensed electrician will reply with next steps and a time to visit.
Homes in South Highpoint also call us for generator installation, emergency electrical calls, a home battery system and JellyFish eave lighting.
Call or text (727) 476-7079 · open 24/7 for emergencies · request a quote online

Home addition electrical in South Highpoint is the new square footage
This page is the new room: a feeder or a subpanel for the addition, new boxes in new framing, new switches at the new door and a clean tie-in at the existing 1970s can. Opening walls in the old house as part of a larger remodel is a different page. A kitchen-only remodel is a different page as well. Here we plan the new footprint first.
Feeders, a subpanel and a tight 1974 can
The typical house here was built around 1974. Most of the local stock predates 1980. That original cabinet may have no spare space and may already carry electric heat. We photograph the can, we add up the new lighting, the new outlets and any 240-volt load in the addition, and we quote a feeder and a subpanel when the old bus cannot take the new room. We will not force a narrow breaker into an unlisted opening.
New framing, a sill and a header
- Florida electrical contractor license EC13014717, licensed & insured
- Woman-owned business based at 6248 Seminole Blvd, Seminole FL 33772
- 2-year workmanship warranty, 5 years with a Member Care Plan
- SPAN Authorized Installer and Home Depot preferred contractor
- Open 24/7 for electrical emergencies: call or text (727) 476-7079
In a stick-built addition we drill the plates, we staple the cable, we set boxes at a consistent height and we sleeve a penetration through a masonry wall when the new room meets a block wall. A header or a beam is not used as a chase. We leave a pull path for a later data cable when you ask for it, and we do not bury a splice in a sealed cavity.
Manufactured homes and a small addition
A manufactured home can take a small addition, but the feeder, the bonding and the interior main have to be checked first. If the pedestal is already tight, that repair is quoted before we land new circuits for the new room. We will not treat a thin manufactured wall like a stick-framed bay.
What we rough in
- A feeder or a subpanel: when the old can cannot carry the new room.
- Lighting and switches: at each new door, with a three-way when the plan asks.
- Receptacles: on the new walls, spaced as required.
- Smoke-alarm feeds: when the addition requires them, as a feed only, not a full detector package.
- A labeled directory: so the new room is easy to find in the old can.
Electric heat and a new room
Nearly every household here heats with electricity. A new room with electric heat is a real load, not a rounding error. We put that number on the quote. If the service is already tight, we say so before the slab or the walls go up, not after the drywall is hung.
Two visits, open walls then devices
The truck is marked. We rough the addition while the walls are open. We meet the inspection if one is required. We return for devices, fixtures and the final directory after the painters are done. If a fixture you chose is not on site, we leave the box safe and we come back.
Permits for a new room
A new addition almost always needs a permit for the electrical work. We handle the paperwork, we are present for the rough and the final, and we do not name a reviewing desk or invent a wait. Unincorporated Pinellas County rules apply to the parcel even when the mail says Pinellas Park or Clearwater.
Warranty on the addition we wire
Labor and the circuits we install in the new room are under a two-year workmanship warranty. Homes on the Member Care Plan at /member-care-plans/ receive five years on that same work. The existing house, except for the tie-in we made, stays outside that promise unless the invoice says otherwise.
A porch enclosure, a knee wall and a sliding-door header
A porch enclosure is still a new room: a knee wall gets receptacles at the right height, a sliding-door header is not drilled into a mess of cables, and the old exterior fixture is either moved or retired so it is not left live in a new closet. We write that fixture plan before the screens come down.
An attic chase and a bath-fan path
When the addition has an attic, we run a neat chase and we keep cable away from a bath fan that already lives in the old attic. A loose loop over insulation is restapled before the drywall goes up.
A leftover patio stub and a new exterior GFCI
Many 1970s houses have a dead patio stub in the slab or in a knee wall. We find it, we cap or we reuse it, and we add a new weather-rated GFCI on the new exterior wall so a grill or a pump is not hanging off a lamp holder. A zipper cord through a window is not the new exterior point.
A sliding-door two-gang and a cable we will not pinch
A new slider gets a two-gang at a reachable height, and we keep cable out of the slider pocket so a later door crew does not pinch it. We mark that pocket on the plate before the drywall goes up.
A hose bib we will not bury in a box
A new exterior wall often has a hose bib nearby. We keep the exterior receptacle off that splash, we use a cover that shuts, and we do not mount a box where a coiled hose will sit on it all summer.
A smoke-alarm interconnect and a new bedroom
If the addition is a bedroom, the new smoke-alarm feed has to interconnect with the existing house where the plan requires it. We run that feed during the rough-in, and we leave the device itself for the finish, or for a later device visit. This is a feed and a location, not a full detector sales package.
A new bath in the addition
If the addition includes a bath, we rough a GFCI for the vanity, a listed fan feed and a light that can take a wet room. That bath is still part of the new square footage, and it is planned with the rest of the addition, not as a surprise at finish.
Common questions
How long does home addition electrical in South Highpoint usually take? A: A simple room with an open can is often a rough-in visit and a finish visit. A new feeder or a tight 1970s service adds a step.
Can you feed the addition from my existing panel? A: Sometimes. If the cabinet is full or the load is tight, we quote a subpanel or a service change first.
Do you wire additions on manufactured homes? A: Yes, once we have looked at the pedestal, the feeder and the bonding and confirmed the new room will fit.
Our shop is on Seminole Blvd, about 7 miles from South Highpoint. Crews work near 49th Street North, Ulmerton Road, Roosevelt Boulevard and 34th Street North. We also serve Largo, Clearwater, Feather Sound, St. Petersburg and Pinellas Park.
Up: Home Addition Electrical across Tampa Bay · For everything we do locally, see South Highpoint electrical service.
Cities next door: Seminole
Call or text (727) 476-7079 for home addition electrical in South Highpoint, or book online. Business hours 7 AM–5 PM, weekend service, 24/7 emergency calls.
