Need dock marine electrical in Bay Pines? Keywest Lights & Electric handles dock marine electrical work in Bay Pines for shore power, boat lifts, dock lights and pumps. We are licensed and woman-owned, and we build for salt water with sealed, corrosion-resistant gear.
Request dock marine electrical in Bay Pines
Tell us what you need and where the work is. A licensed electrician will reply with next steps and a time to visit.
Other work we do in Bay Pines: JellyFish eave lighting, backup generator hookups, home EV charging and panel upgrades.
Call or text (727) 476-7079 · open 24/7 for emergencies · request a quote online

Dock marine electrical in Bay Pines: safe power at the water’s edge
Boca Ciega Bay and Long Bayou touch this community, and about two-fifths of its area is water. Many homes have docks, davits, lifts or seawalls. Electricity near water needs special care. A small leak of current can be deadly to a swimmer, so every dock circuit needs proper protection and clean connections.
What we install and repair
- Shore power pedestals: 30 amp and 50 amp boat connections.
- Boat lift circuits: motors, switches and disconnects.
- Dock lighting: low-profile LED fixtures and photocells.
- Pumps and aerators: bilge, wash-down and irrigation.
- Seawall outlets: weather-protected receptacles.
- Marine grounding: bonding, corrosion checks and tests.
Why protection is critical
- Florida electrical contractor license EC13014717, licensed & insured
- Woman-owned business based at 6248 Seminole Blvd, Seminole FL 33772
- 2-year workmanship warranty, 5 years with a Member Care Plan
- SPAN Authorized Installer and Home Depot preferred contractor
- Open 24/7 for electrical emergencies: call or text (727) 476-7079
Water conducts, and salt makes it better. Ground-fault protection stops current if it leaks to the water. We install protection at the source and test it. Equipment leakage protection and a clearly labeled disconnect keep boaters and swimmers safe. Any old dock without protection is a hazard.
Wire, conduit and fittings
Marine wiring uses stranded copper with tinned strands, sealed connectors and cable rated for wet service. Conduit is PVC or liquid-tight with stainless clamps. Brass and stainless fittings resist salt where plain steel would rust in a season. We avoid dissimilar metals that corrode each other.
Shore power basics
A pedestal supplies 30 or 50 amps to a boat. The boat’s inlet, the cord and the dock must all match. We check polarity, grounds and breaker size, and we explain galvanic isolation to owners who want to prevent stray current corrosion.
Boat lifts
A lift uses a motor, a limit switch and a control. We provide a disconnect in view of the lift, ground-fault protection and a switch at a comfortable height. When the motor trips often, we check for water in the box and a worn capacitor.
Dock lights
Dock lights should be low glare, dark-sky friendly and corrosion resistant. We use sealed LED fixtures, timers and photocells. Warm color light attracts fewer insects than harsh white.
Storm preparation
Before a storm, shut off the dock breaker. After a storm, inspect for debris in boxes and water in conduits. We offer post-storm inspections so you do not re-energize a damaged circuit. Surge protection at the dock panel reduces damage from lightning.
Corrosion checks
Green, white or black crust on a terminal means corrosion. We clean, coat and replace parts as needed, and note where moisture finds a way in. A yearly check catches problems before a breaker trips.
Neighbors, associations and shared docks
Some docks serve several homes or a condo group. We map each circuit, label every breaker and put a lockable disconnect at the shoreline. A clear map helps in an emergency.
Inspections and permits
Dock electrical work follows code rules for marinas and docks. We prepare the permit paperwork and meet the inspector. Seawall and dock construction may need other approvals. We stay in our lane and coordinate with your dock builder.
Warranty
Workmanship carries a 2-year warranty, or 5 years with a Member Care Plan. Call or text (727) 476-7079.
Understanding stray current and galvanic corrosion
Boats and docks sit in electrolyte water. A small leak from a faulty bilge pump, a bad ground or a neighbor’s boat can drive current through metal parts and eat zinc, propellers and fittings. A galvanic isolator, bonded grounds and a clean shore cord reduce the risk. We test for stray current with a meter and a reference electrode and explain what the numbers mean.
Tides, wave action and cable support
Cable that swings with the water fatigues at the connection. We strap runs every few feet with stainless hardware, leave a drip loop and use a flexible section where the dock moves. Floating docks need slack and guides so the cable does not stretch tight at low tide.
Dock boxes, junctions and covers
A junction box on a piling takes a beating from spray, bird droppings and sun. We choose gasketed boxes with UV-stable covers, mount them above splash height and seal every hub with a marine-grade fitting. A cover that closes with a tight latch keeps the inside dry between storms.
Fish cleaning stations, wash-down outlets and fountains
Outlets near a cleaning table or a fountain see constant splash. We use weather-resistant ground-fault outlets in covers that stay closed while a cord is plugged in, and we mount them away from the splash zone. Anything with a pump gets its own protected circuit.
Kayak racks, lanai-to-dock paths and path lighting
A dark path to a dock is a fall hazard. Low-voltage path lights on a timer guide the way without glare, and a motion light at the end of the dock helps with late returns. We run the cable in conduit under pavers or along the edge.
Common questions
Do I need ground-fault protection on my dock? Yes. It is critical for safety.
Can you add a boat lift circuit? Yes, with a disconnect and protection.
Why does my dock breaker keep tripping? Water in a box, a failing motor or a leaking fixture. We test and fix it.
Do you work on seawalls? We handle electrical only. Your dock builder handles structure.
Can you install LED dock lights? Yes, on a timer or photocell.
How often should a dock be inspected? Yearly, and after a storm.
Our trucks leave the shop on Seminole Blvd, about a mile away, and work near Boca Ciega Bay, Bay Pines Boulevard, Long Bayou and Seminole Boulevard. We also serve North Redington Beach, Redington Beach, Madeira Beach, Redington Shores and Pinellas Park.
Up: Dock Marine Electrical across Tampa Bay · For everything we do locally, see Bay Pines electrical service.
Nearby: Madeira Beach · Redington Beach · North Redington Beach · Bardmoor
Call or text (727) 476-7079 for dock marine electrical in Bay Pines, or book online. Business hours 7 AM–5 PM, weekend service, 24/7 emergency calls.
